Nissan Rogue Service Manual: Precaution

Nissan Rogue Service Manual / Restraints / Seat Belt / Precaution

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SR and SB section of this Service Manual.

WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the battery and wait at least three minutes before performing any service.

Precaution for Seat Belt Service

CAUTION:

Before removing the seat belt pre-tensioner assembly, turn the ignition switch OFF, disconnect both battery terminals and wait at least three minutes. For approximately three minutes after the battery terminals have been removed, it is still possible for the air bag and seat belt pre-tensioner to deploy.
Therefore, do not attempt work on any SRS connectors or wires until at least three minutes have passed.
After replacing or reinstalling seat belt pre-tensioner assembly or reconnecting seat belt pre-tensioner assembly connector, make sure entire SRS operates properly. Refer to SRC-16, "On Board Diagnosis Function".
Do not disassemble buckle or seat belt assembly.
Replace anchor bolts if they are deformed or worn out.
Do not oil tongue or buckle.
If any component of seat belt assembly is questionable, do not repair. Replace the whole seat belt assembly.
If webbing is cut, frayed or damaged, replace seat belt assembly.
When replacing seat belt assembly, use a genuine NISSAN seat belt assembly.

Precaution for Work

When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and prevent them from being dropped.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with a new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After installation is complete, be sure to check that each part works properly.
Follow the steps below to clean components:

Water soluble dirt:

Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
Then rub with a soft, dry cloth.

Oily dirt:

Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
Then rub with a soft, dry cloth.

Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
For genuine leather seats, use a genuine leather seat cleaner.

Seat Belt

...

Preparation

Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (J-46534) Trim Tool Set ...

Other materials:

Key switch signal circuit (without intelligent key)
Description Transmits a key switch signal to the BCM. Component Function Check 1. CHECK BCM INPUT SIGNAL Select "Data Monitor" for "BCM" and check the "KEY ON SW" monitor value. Is the inspection result normal? YES >> Inspection End. NO >> Refer ...

Flexible seating
WARNING Never allow anyone to ride in the cargo area or on the rear seats when they are in the fold-down position. In a collision, people riding in these areas without proper restraints are more likely to be seriously injured or killed. Do not allow peo ...

VIN registration
Description VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced. NOTE: Accurate VIN which is registered in ECM may be required for Inspection & Maintenance (I/M). Work Procedure 1.CHECK VIN Check the VIN of the vehicle and note it. ...