Nissan Rogue (T33) 2021-Present Service Manual: P2616 Intake Camshaft Position Sensor
DTC Description
DTC DETECTION LOGIC
| DTC |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition | ||
| P2616 | 00 |
A camshaft posi signal B1 (Camshaft A Position Signal Output Circuit High Bank 1) |
Diagnosis condition | Engine running at idle |
| Signal (terminal) | Intake camshaft position sensor signal for electric intake valve timing control | |||
| Threshold | The intake camshaft position sensor signal edge count is more than 4 counts per one camshaft rotation | |||
| Diagnosis delay time | 1 second | |||
POSSIBLE CAUSE
Harness or connectors [Intake camshaft position sensor signal circuit for electric intake valve timing control is open or shorted.]
FAIL-SAFE
Engine Control System
| Fail safe mode | Nissan Ariya Vehicle behavior | |
|---|---|---|
| Device fix mode |
|
|
| Combustion control mode | Stratified charge combustion control at starting | No stratified charge combustion at starting (cold start). |
Stop/Start System
When a DTC is detected, the stop/start indicator lamp blinks slowly and the stop/start system operation is prohibited.
When ECM detects error while operating the stop/start system, ECM restarts the engine.
DTC Confirmation Procedure
CHECK DTC PRIORITY
If DTC P2616 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.
Is DTC P0340 detected?
YES>>Perform diagnosis of applicable. Refer to DTC Description.
NO>>GO TO 2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
-
Start the engine and wait at least 5 seconds.
-
Check 1st trip DTC.
Is DTC P2616 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK DTC PRIORITY
If DTC P2616 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.
Is DTC P0340 detected?
YES>>Perform diagnosis of applicable. Refer to DTC Description.
NO>>GO TO 2.
CHECK INTAKE CAMSHAFT POSITION (CMP) SENSOR SIGNAL CIRCUIT FOR ELECTRIC INTAKE VALVE TIMING CONTROL
-
Ignition switch OFF.
-
Disconnect ECM harness connector and electric intake valve timing control module harness connector.
-
Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.
ECM Electric intake valve timing control module Continuity Connector Terminal Connector Terminal F71 127 F113 37 Existed -
Also check harness for short to power and short to ground.
Is the inspection result normal?
YES>>INSPECTION END
NO>>Repair or replace error-detected parts.
Other materials:
Abs Branch Line Circuit
Diagnosis Procedure
CHECK CONNECTOR
Turn the ignition switch OFF.
Disconnect the battery cable from the negative terminal.
Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side).
ABS actuator and electric unit (control u ...
Intelligent Around View Monitor system
limitations
Basic information
WARNING
Listed below are the system limitations for the Intelligent Around View Monitor. Failure to drive your Nissan Rogue in accordance with these limitations could result in serious injury or death.
Do not use the Intelligent Around View Monitor with the outside
mirrors in th ...
Exterior front
Hood — the main exterior panel covering the engine compartment of the Nissan Rogue.
Windshield wiper and washer
Switch operation — controls for activating the Rogue’s windshield wipers.
Window washer fluid — reservoir and spray system for cleaning the windshield.
Windsh ...