Nissan Rogue Owners Manual: Text messaging

Nissan Rogue Owners Manual / Monitor, climate, audio, phone and voice recognition systems / Bluetooth® Hands-Free Phone System with Navigation System (if so equipped) / Text messaging

WARNING

Laws in some jurisdictions may restrict the use of “Text-to-Speech”. Check local regulations before using this feature.
Laws in some jurisdictions may restrict the use of some of the applications and features, such as social networking and texting. Check local regulations for any requirements.
Use the text messaging feature after stopping your vehicle in a safe location.
If you have to use the feature while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
If you are unable to devote full attention to vehicle operation while using the text messaging feature, pull off the road to a safe location and stop your vehicle.

The system allows for the sending and receiving of text messages through the vehicle interface.

Sending a text message:

Press the button on the steering wheel.
Say “Phone” after the tone.
Say “Send Text” after the tone.
The system will provide a list of available commands in order to determine the recipient of the text message. Choose from the following:

To (a name)
Enter Number
Missed Calls
Incoming Calls
Outgoing Calls

For additional information about these options, refer to “Voice commands” in this section.

Once a recipient is chosen, the system prompts for which message to send. Nine predefined messages are available as well as three custom messages. To choose one of the predefined messages, speak one of the following after the tone:

“Driving, can’t text”
“Call me”
“On my way”
“Running late”
“Okay”
“Yes”
“No”
“Where are you?”
“When?”

To send one of the custom messages, say “Custom Messages”. If more than one custom message is stored, the system will prompt for the number of the desired custom message.

For additional information on setting and managing custom text messages, refer to “Bluetooth® settings” in this section.

Reading a received text message:

Press the button on the steering wheel.
Say “Phone” after the tone.
Say “Read Text” after the tone.

The text message, sender and delivery time are shown on the screen. Use the tuning switch to scroll through all text messages if more than one are available. Press the button to exit the text message screen. Press the button to access the following options for replying to the text message:

Call Back
Speak this command to call the sender of the text message using the Bluetooth® Hands-Free Phone System.
Send Text
Speak this command to send a text message response to the sender of the text message.
Read Text
Speak this command to read the text message again.
Previous Text
Speak this command to move to the previous text message (if available).
Next Text
Speak this command to move to the next text message (if available).

NOTE: Text messages are only displayed if the vehicle speed is less than 5 mph (8 km/h).

Vehicle phonebook

To access the vehicle phonebook: Press the button on the control panel. Touch the “Phonebook” key. Choose the desired entry from the displayed list. The num ...

Phone settings

To access the phone settings: Press the [ ] button. Touch the “Settings” key. Touch the “Phone & Bluetooth” key. . Touch the “Phone Settings” key and adjust ...

Other materials:

Adjustment of steering angle sensor neutral position
Description Refer to the table below to determine if adjustment of steering angle sensor neutral position is required. Work Procedure ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION CAUTION: To adjust neutral position of steering angle sensor, make sure to use CONSULT. (Adjustment ...

Information display is malfunctioning
Diagnosis Procedure 1.CHECK DTC WITH ECM Check that DTC is not displayed. Is the inspection result normal? YES >> GO TO 2. NO >> Perform trouble diagnosis relevant to DTC indicated. 2.CHECK INFORMATION DISPLAY (ASCD) Refer to EC-475, "Component Function Check". Is ...

P062F EEPROM
Description TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated value does not agree with the stored value, TCM judges this as a malfunction. DTC Description TCM compares the calculated value stored in the flash ROM with the value stored ...