Nissan Rogue manuals

Nissan Rogue Service Manual: Removal and installation

Nissan Rogue Service Manual / Driver information & multimedia / Audio, Visual & Navigation System / Display audio / Removal and installation

AUDIO UNIT

Exploded View

Exploded View

  1. Audio unit bracket (LH)
  2. Audio unit
  3.  Audio unit bracket (RH)

Removal and Installation

REMOVAL

  1.  Disconnect the negative battery terminal. Refer to PG-75, "Removal and Installation (Battery)".
  2.  Remove A/C switch (AUTOMATIC AIR CONDITIONING) or front air control (MANUAL AIR CONDITIONING).

    Refer to HAC-102, "Removal and Installation" (AUTOMATIC AIR CONDITIONING) or HAC-181, "Removal and Installation" (MANUAL AIR CONDITIONING).

  3.  Remove instrument finisher B. Refer to IP-16, "INSTRUMENT FINISHER B : Removal and Installation".
  4.  Remove instrument finisher E. Refer to IP-16, "INSTRUMENT FINISHER E : Removal and Installation".
  5.  Remove the audio unit screws, then pull out the audio unit.
  6.  Disconnect the harness connectors from the audio unit and remove.
  7.  Remove the audio unit bracket (LH/RH) screws and the audio unit brackets (LH/RH) (if necessary).

INSTALLATION

Installation is in the reverse order of removal.

STEERING SWITCHES

Exploded View

Exploded View

  1. Steering wheel rear finisher
  2. Steering wheel
  3.  Steering switches

Pawl

Removal and Installation

REMOVAL

NOTE: The steering switches are serviced as an assembly.

  1.  Remove steering wheel. Refer to ST-11, "Removal and Installation".
  2.  Release pawls on the steering wheel rear finisher and remove.
  3.  Remove screws (A) and steering switches (1) from steering wheel (2).

Removal

INSTALLATION

Installation is in the reverse order of removal.

FRONT TWEETER

Removal and Installation

REMOVAL

  1.  Remove defroster grille. Refer to VTL-12, "DEFROSTER GRILLE : Removal and Installation".
  2.  Remove bolts and pull out the front tweeter.
  3.  Disconnect the harness connector from the front tweeter and remove.

INSTALLATION

Installation is in the reverse order of removal.

FRONT DOOR SPEAKER

Exploded View

Exploded View

  1. Front door speaker

Removal and Installation

REMOVAL

  1.  Remove front door finisher. Refer to INT-15, "Removal and Installation".
  2.  Remove front door speaker bolts, then pull out front door speaker.
  3.  Disconnect the harness connector from front door speaker and remove.

INSTALLATION

Installation is in the reverse order of removal.

REAR DOOR SPEAKER

Exploded View

Exploded View

  1. Rear door speaker

Removal and Installation

REMOVAL

  1.  Remove rear door finisher. Refer to INT-18, "Removal and Installation".
  2.  Remove rear door speaker bolts, then pull out rear door speaker.
  3.  Disconnect the harness connector from the rear door speaker and remove.

INSTALLATION

Installation is in the reverse order of removal.

USB INTERFACE AND AUX IN JACK

Removal and Installation

REMOVAL

  1.  Remove cluster lid C. Refer to IP-21, "Removal and Installation".
  2.  Release the pawls (A) on the back of USB interface and AUX in jack (2), then remove from the front of cluster lid C (1).

Removal

INSTALLATION

Installation is in the reverse order of removal.

MICROPHONE

Removal and Installation

REMOVAL

  1.  Remove the map lamp assembly. Refer to INL-55, "Removal and Installation".
  2.  Release harness connector (A) by sliding rearward to remove from the pawl (B).
  3.  Release pawls (C) and remove the microphone (1) from the front room/map lamp assembly.

Removal

INSTALLATION

Installation is in the reverse order of removal.

REAR VIEW CAMERA

Removal and Installation

REMOVAL

  1.  Remove the back door outer finisher. Refer to EXT-50, "Removal and Installation".
  2.  Release pawl, disconnect harness connector from rear view camera and remove.

INSTALLATION

Installation is in the reverse order of removal.

AUDIO ANTENNA

Removal and Installation

REMOVAL

  1.  Remove the luggage side upper finisher (RH). Refer to INT-36, "LUGGAGE SIDE UPPER FINISHER : Removal and Installation".
  2.  Partially lower headlining (rear). Refer to INT-30, "Removal and Installation".
  3.  Disconnect harness connectors from antenna feeder.
  4.  Remove nut from audio antenna and remove.

INSTALLATION

Installation is in the reverse order of removal.

Audio antenna nut : 6.5 N·m (0.66 kg-m, 58 in-lb)

CAUTION: If the audio antenna nut is not properly tightened, lower sensitivity of the antenna may be experienced.

If the nut is over tightened, this will deform the roof panel.

ANTENNA FEEDER

Feeder Layout

ANTENNA FEEDER LAYOUT

Feeder Layout

  1. Antenna base (antenna amp. and satellite antenna)
  2. Rod Antenna
  3. M503
  4.  M502
  5. M130, M501
  6. M129, M500
  7.  M126
  8.  M124
Symptom diagnosis
AUDIO SYSTEM Symptom Table RELATED TO AUDIO Symptoms Check items Probable malfunction location The disk cannot be removed Audio unit Malfunction in audio uni ...

Navigation without bose
...

Other materials:

P0197, P0198 EOT sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0197 EOT SEN/CIRC (Engine oil temperature sensor low) An excessively low voltage from the engine oil temperature sensor is sent to ECM. ...

Power outlets
Instrument Panel 12V OUTLETS The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 volt, 120W (10A) maximum. The front and center console power outlets are powered only when the ignition switch is in the ACC (if so equipped) or ON po ...

Exterior and interior lights
Item Wattage (W) Bulb No. Headlight assembly*       High 65 H9 Low 55 H11 Park 5 W5W Turn 28/8 7444 Sidemarker 5 WY5W Front fog lights (if so equipped) 55 H11 ...

© 2014-2025 Copyright www.nirogue.com