Nissan Rogue Owners Manual: Windows

Nissan Rogue Owners Manual / Instruments and controls / Windows

POWER WINDOWS

WARNING

Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows.
Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents.

The power windows operate when the ignition switch is placed in the ON position, or for a period of time after the ignition switch is placed in the OFF position. If the driver’s or passenger’s door is opened during this period of time, the power to the windows is canceled.

Power windows

Window lock button
Power door lock switch
Driver side automatic switch
Front passenger side switch
Left rear passenger side switch
Right rear passenger side switch

Driver’s side power window switch

The driver’s side control panel is equipped with switches to open or close all of the windows.

To open a window, push the switch to the first detent and continue to hold down until the desired window position is reached. To close a window, pull the switch to the first detent and continue to hold up until the desired window position is reached.

Locking passengers’ windows

When the window lock switch is depressed, only the driver’s side window can be opened or closed. Push it again to cancel the window lock function.

Front passenger’s power window switch

The passenger’s window switch operates only the corresponding passenger’s window. To open the window partially, push the switch down 1 lightly until the desired window position is reached. To close the window partially, pull the switch up 2 until the desired window position is reached.

Rear power window switch

The rear power window switches open or close only the corresponding windows. To open the window, push the switch and hold it down 1 . To close the window, pull the switch up 2 .

Automatic operation

To fully open a window, press the window switch down to the second detent and release it; it need not be held. The window automatically opens all the way. To stop the window, lift the switch up while the window is opening.

To fully close a window, pull the switch up to the second detent and release it; it need not be held.

To stop the window, press the switch down while the window is closing.

Auto-reverse function

The auto-reverse function can be activated when a window is closed by automatic operation.

Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs.

WARNING

There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.

If the vehicle’s battery is disconnected, replaced, or jump started, the power window auto-reverse function may not operate properly. If this occurs, please contact the dealer to re-initialize the power window auto-reverse system.

If the control unit detects something caught in a window equipped with automatic operation as it is closing, the window will be immediately lowered.

Divide-n-hide® adjustable floor (if so equipped)

Divide-n-hide® adjustable floor (if so equipped) WARNINGDo not put objects heavier than 165 lbs (75 kg) on the Divide-N-Hide® while in the mid position. In the upper position, obje ...

Power panoramic moonroof (if so equipped)

The moonroof will only operate when the ignition switch is placed in the ON position. The moonroof is operational for a period of time, even if the ignition switch is placed in the ACC (if so ...

Other materials:

C1716, C1717, C1718, C1719 transmitter (pressure data)
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure reported by the TPMS sensor Read TPMS DTC ...

Low tire pressure warning lamp stays on
Low Tire Pressure Warning Lamp Stays On When Ignition Switch Is Turned On 1.CHECK BCM CONNECTORS Turn ignition switch OFF. Disconnect BCM connectors. Check terminals for damage or loose connections. Is the inspection result normal? YES >> GO TO 2. NO >> Repair ...

Unit disassembly and assembly
STEERING GEAR AND LINKAGE Exploded View DISASSEMBLY AND ASSEMBLY Steering gear Inner boot clamp Boot Outer boot clamp Outer socket Disassembly and Assembly DISASSEMBLY Remove outer socket lock nut and remove outer socket. Remove inne ...