Nissan Rogue Service Manual: Water hose

Nissan Rogue Service Manual / Transmission & driveline / Transaxle & Transmission / Removal and installation / Water hose

Exploded View

Exploded View

Water outlet
Hose clamp
Water hose A
Clip
CVT oil warmer
Transaxle assembly
Water hose B
Heater thermostat
Water hose C

: Always replace after every disassembly.
: N·m (kg-m, ft-lb)

Removal and Installation

REMOVAL

WARNING: Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.

CAUTION: Perform when the engine is cold.

NOTE: When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spilling.

Remove battery tray. Refer to PG-76, "Removal and Installation (Battery Tray)".
Remove engine under cover. Refer to EXT-16, "Exploded View".
Remove CVT fluid charging pipe. Refer to TM-220, "Exploded View".
Remove fender protector side cover. Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
Remove water hose A, B, C, and heater thermostat.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

Do not reuse hose clamps.
Do not reuse hose clip
Securely install the water hose clip to the bracket hole of charging pipe.
Refer to the following when installing water hoses.

Installation

Refer to the followings when installing hose clamp.

CAUTION: Hose clamp should not interfere with the bulge of tube.

Installation

Inspection

INSPECTION AFTER REMOVAL

Heater Thermostat

Fully immerse the heater thermostat 1 in a container (A) filled with water. Continue heating the water while stirring.
Continue heating the heater thermostat for 5 minutes or more after bringing the water to a boil.

Heater Thermostat

Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.

Place dial indicator (A) on the pellet B and measure the elongation from the initial state.

Heater Thermostat

Standard : Refer to TM-226, "Heater Thermostat".

If out of standard, replace heater thermostat.

INSPECTION AFTER INSTALLATION

Start the engine, and check the joints for coolant leakage.

Differential side oil seal

Exploded View Transaxle assembly Differential side oil seal (left side) Differential side oil seal (right side) (FWD models only) : Always replace after every disassembly. : Appl ...

Fluid cooler hose

Exploded View COMPONENT PARTS LOCATION Transaxle assembly Fluid cooler hose A Hose clamp Fluid cooler hose B CVT oil warmer To radiator : Always replace after every disassem ...

Other materials:

Headlight control switch
Type A (if so equipped) When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. When turning the switch to the position, the headlights come on and all the other lights remain on. Type B (if so equipped) ...

Service data and specifications (SDS)
General Specification GENERAL SPECIFICATIONS ( ): Valve timing control “ON” Drive belt Spark Plug Intake Manifold Exhaust Manifold Camshaft *1: Cam wear limit *2: Total indicator reading VALVE LIFTER VALVE CLEARANCE *: Approximately 80°C (176°F) AVAIL ...

P0300, P0301, P0302, P0303, P0304 misfire
DTC Description DTC DETECTION LOGIC When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor (POS) signal to vary, ECM can determine that a misfire is occurring. Sensor Input signal to ECM ECM functio ...