Nissan Rogue manuals

Nissan Rogue Service Manual: VDC off switch

Component Function Check

1.CHECK VDC OFF SWITCH OPERATION

Check that VDC OFF indicator lamp in combination meter turns ON/OFF when VDC OFF switch is operated.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to BRC-117, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK VDC OFF SWITCH CIRCUIT

  1.  Turn the ignition switch OFF.
  2.  Disconnect ABS actuator and electric unit (control unit) harness connector.
  3.  Disconnect VDC OFF switch harness connector.
  4.  Check the continuity between ABS actuator and electric unit (control unit) harness connector and VDC OFF switch harness connector.

Check VDC off switch circuit

  1. Check the continuity between ABS actuator and electric unit (control unit) harness connector and ground.

Check VDC off switch circuit

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace error-detected parts.

2.CHECK VDC OFF SWITCH GROUND CIRCUIT

Check the continuity between VDC OFF switch harness connector and ground.

Check VDC off switch ground circuit

the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK VDC OFF SWITCH

Check the VDC OFF switch. Refer to BRC-118, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the VDC OFF switch. Refer to BRC-138, "Removal and Installation".

4.CHECK VDC OFF SWITCH SIGNAL

With CONSULT

  1.  Connect ABS actuator and electric unit (control unit) harness connector.
  2.  Connect VDC OFF switch harness connector.
  3.  Select “ABS”, “DATA MONITOR” and “OFF SW” according to this order. Check the VDC OFF switch signal.

Check VDC off switch signal

Is the inspection result normal? YES >> Inspection End.

NO >> GO TO 5.

5.CHECK TERMINAL

  1.  Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.
  2.  Check the VDC OFF switch pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Repair or replace error-detected parts.

Component Inspection

1.CHECK VDC OFF SWITCH

  1.  Turn the ignition switch OFF.
  2.  Disconnect VDC OFF switch harness connector.
  3.  Check the continuity between terminals of VDC OFF switch connector.

Check VDC off switch

Is the inspection result normal? YES >> Inspection End.

NO >> Replace the VDC OFF switch. Refer to BRC-138, "Removal and Installation".

Parking brake switch
Component Function Check 1.CHECK PARKING BRAKE SWITCH OPERATION Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated. Is the inspection result normal? ...

ABC warning lamp
Component Function Check 1.CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for 1 second after ignition switch is turned ON. CAUTION: Never start the eng ...

Other materials:

Disassembly and assembly
FUEL LEVEL SENSOR UNIT Exploded View Fuel Level Sensor Unit Fuel filter and pump assembly Fuel level sensor unit Float arm assembly Fuel tank temperature sensor Disassembly and Assembly NOTE: Fuel level sensor unit and fuel tank temperature sensor are replaced as and assembl ...

ECU diagnosis information
TCM Reference Value CONSULT DATA MONITOR STANDARD VALUE  In CONSULT, electric shift timing or lock-up timing, i.e. operation timing of each solenoid valve, is displayed. Therefore, if there is an obvious difference between the shift timing estimated from a shift shock (or engine ...

Circuit inspection
DESCRIPTION  In general, testing electrical circuits is an easy task if it is approached in a logical and organized method. Before beginning it is important to have all available information on the system to be tested. Also, get a thorough understanding of system operation. Then y ...

© 2014-2022 Copyright www.nirogue.com