Nissan Rogue Service Manual: Valve timing control
Exploded View

- Valve timing cover
- 2. O-rings
- Intake valve timing intermediate
lock control solenoid valve
- Intake valve timing control solenoid
valve
- Exhaust valve timing control solenoid
valve
Intake Valve Timing Intermediate Lock Control Solenoid Valve, Intake Valve
Timing
Control Solenoid Valve, and Exhaust Valve Timing Control Solenoid Valve
REMOVAL
- Disconnect the battery negative terminal. Refer to PG-75,
"Exploded View"
- Remove cowl top extension. Refer to EXT-25, "Removal and
Installation".
- Remove the RH engine mount torque rod. Refer to EM-81, "Exploded
View".
- Use a suitable jack (A) to securely support the bottom of the
engine (1) and the transaxle assembly (2).
CAUTION:
Put a piece of wood or an equivalent as the supporting surface
and secure in a stable condition.

- Remove A/C line bracket bolt.
- Remove harness grounds from engine mounting bracket (RH).
- Remove harness retainers from engine mounting bracket (RH).
- Remove the engine mounting bracket (RH). Refer to EM-81, "Exploded
View"
- Remove the RH engine mounting support bracket. Refer to EM-81,
"Exploded View".
- Remove the RH engine mount torque rod. Refer to EM-81, "Exploded
View".
- Disconnect harness connectors from intake valve timing
intermediate lock control solenoid valve, intake
valve timing control solenoid valve, and exhaust valve timing control
solenoid valve connectors.
- Remove intake valve timing intermediate lock control solenoid valve,
intake valve timing control solenoid
valve, and exhaust valve timing control solenoid valve bolts.
- Remove intake valve timing intermediate lock control solenoid
valve, intake valve timing control solenoid
valve, exhaust valve timing control solenoid valve from valve timing control
cover.
- . Remove O-rings from intake valve timing intermediate lock control
solenoid valve, intake valve timing control
solenoid valve, and exhaust valve timing control solenoid valve.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
- Do not reuse O-rings.
- Lubricate O-rings with clean engine oil before installing.
Valve Timing Control Cover
REMOVAL
- Remove the intake valve timing intermediate lock control solenoid
valve, intake valve timing control solenoid
valve, exhaust valve timing control solenoid valve. Refer to EM-74, "Intake
Valve Timing Intermediate
Lock Control Solenoid Valve, Intake Valve Timing Control Solenoid Valve, and
Exhaust Valve Timing Control
Solenoid Valve".
- Remove harness grounds and retainers from the top if the engine
mount bracket.
- Loosen the valve timing control cover bolts in the reverse order
shown.
- Remove the valve timing control cover bolts.

- Remove the valve timing control cover by cutting the liquid gasket
using Tool (A).

Tool number : KV10111100 (J-37228)
NOTE:
Do not loosen screws (A) on the back of the valve timing control
cover.

INSTALLATION
- Install valve timing control cover with the following procedure.
- Install intake valve timing intermediate lock control solenoid
valve, intake valve timing control solenoid
valve and exhaust valve timing control solenoid valve to valve timing
control cover.
- Install O-ring to front cover side.
CAUTION:
Do not reuse O-ring.
- Apply liquid gasket to the positions shown. Refer to GI-22,
"Recommended
Chemical Products and Sealants".

Diameter (A) : 3.4 - 4.4 mm (0.134 - 0.173 in)
- Install valve timing control cover.
- Tighten the bolts to specification in the numerical order shown.

Exploded View
Camshaft position sensor (INT)
O-ring
Camshaft brackets (INT)
Camshaft brackets (EXH)
Camshaft (INT)
O-ring
Camshaft bracket (No. 1)
Camshaft sproc ...
VALVE OIL SEAL
VALVE OIL SEAL : Removal and Installation
REMOVAL
Remove camshafts. Refer to EM-64, "Removal and Installation".
Remove valve lifters. Refer to EM-56, " ...
Other materials:
P0841 transmission fluid pressure SEN/SW A
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
P0841
FLUID PRESS SEN/SW A
(Transmission Fluid Pressure Sensor/Switch
“A” Circuit Range/Performance)
When all of the following conditions are sa ...
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
Starting the engine (models with NISSAN
Intelligent Key® system)
Apply the parking brake.
Move the shift lever to P (Park) or N (Neutral).
P (Park) is recommended.
The starter is designed not to operate if
the shift lever is in any of the driving
positions.
Push the ignition switch to the ON position.
Depress the brake pedal and pus ...
© 2014-2025 Copyright www.nirogue.com