Nissan Rogue Service Manual: Unit removal and installation
FRONT SUSPENSION MEMBER
Exploded View

- Front suspension member
- Strut mounting bearing
- Rebound stopper insulator
- Rebound stopper
Removal and Installation
REMOVAL
- Remove the wheel and tire using power tool. Refer to WT-60,
"Removal and Installation".
- Remove side under cover. Refer to EXT-37, "ENGINE UNDER COVER : Removal
and Installation".
- Remove the bolt and separate the front wheel sensor from the
steering knuckle. Separate the harness
from the brackets and position aside. Refer to BRC-132, "FRONT WHEEL SENSOR
: Exploded View".
CAUTION:
- Failure to separate the front wheel sensor from the steering
knuckle may result in damage to the
front wheel sensor.
- Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on wheel
sensor harness.
- Remove the nut and separate the stabilizer connecting rod from the strut
bracket.
- Remove the cotter pin and nut, and separate the outer socket from
the steering knuckle.
- Remove the bolt and separate steering column yoke from steering
gear. Refer to ST-12, "Exploded View".
- Remove transverse link from steering knuckle. Refer to FAX-9,
"Exploded View" (FWD), FAX-40,
"Exploded View" (AWD).
- Remove rear torque rod. Refer to EM-81, "Exploded View".
- Set suitable jack front suspension member.
- Remove front suspension member stay from vehicle.
- Remove bolts and nuts of front suspension member.
- Gradually lower jack to remove front suspension assembly from
vehicle.
CAUTION:
Secure suspension assembly to suitable jack while removing
it.
- Remove bolts and nuts, and then remove transverse link, stabilizer
bar from front suspension member.

INSTALLATION
Installation is in the reverse order of removal.
- Install the suspension member bolts in the order shown.
1-2 temporary tightening
3-5 torque to specification Refer to FSU-20, "Exploded View".

: Front
- Perform final tightening of installation position between front
suspension
member and transverse links (rubber bushing) under
unladen condition with tires on level ground.
- Check wheel sensor harness for proper connection. Refer to BRC-
132, "FRONT WHEEL SENSOR : Exploded View".
Inspection
INSPECTION AFTER REMOVAL
Check the front suspension member for significant deformation, cracks, or
damages. Replace it if necessary.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to FSU-7, "Inspection".
FRONT COIL SPRING AND STRUT
Exploded View
Strut mount insulator
Rotary stop
Front spring upper rubber seat
Front suspension bound bumper
Front spring
Front spring lower ru ...
FRONT COIL SPRING AND STRUT
Exploded View
Strut mount insulator
Rotary Stop
Front spring upper rubber seat
Front suspension bound bumper
Front spring
Front spring lo ...
Other materials:
Precautions on seat belt usage
If you are wearing your seat belt properly adjusted
and you are sitting upright and well back in
your seat with both feet on the floor, your chances
of being injured or killed in a collision and/or the
severity of injury may be greatly reduced.
NISSAN strongly encourages you and all of yo ...
Interior room lamp control circuit
Description
Controls each interior room lamp (ground side) by PWM signal.
NOTE:
PWM signal control period is approximately 250 Hz (in the gradual
brightening/dimming).
Component Function Check
CAUTION:
Before performing the diagnosis, check that the following is normal.
Interior ro ...
P0116 ECT sensor
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
P0116
ECT SENSOR
(Engine coolant temperature sensor 1 circuit
range/performance)
The comparison result of signals transmitted to ECM from each
...
В© 2014-2025 Copyright www.nirogue.com