Nissan Rogue Service Manual: System

Nissan Rogue Service Manual / Body exterior, doors, roof & vehicle security / Power Window Control System / System description / System

System Description

SYSTEM DIAGRAM

System diagram

POWER WINDOW OPERATION

Main power window and door lock/unlock switch can open/close all windows.
Front and rear power window switches can open/close the corresponding windows.

POWER WINDOW AUTO-OPERATION (FRONT DRIVER SIDE)

AUTO UP/DOWN operation can be performed when main power window and door lock/unlock switch turns to AUTO.
Encoder continues detecting the movement of power window motor and transmits to power window switch as the encoder pulse signal while power window motor is operating.
Power window switch reads the changes of encoder signal and stops AUTO operation when door glass is at fully opened/closed position.
Power window motor is operable in case encoder is malfunctioning.

RETAINED POWER OPERATION

Retained power operation is an additional power supply function that enables power window system to operate for 45 seconds even when power switch is turned OFF.

RETAINED POWER CANCEL CONDITIONS

Front door CLOSE (door switch OFF) → OPEN (door switch ON).
When power switch is ON again.
When timer time passes (45 seconds).

POWER WINDOW LOCK

Ground circuit inside main power window and door lock/unlock switch shuts off when power window lock switch is ON. This inhibits power window switch operation except with the main power window and door lock/ unlock switch.

ANTI-PINCH SYSTEM (FRONT DRIVER SIDE)

Pinch foreign material in the door glass during AUTO-UP operation, and it is the anti-pinch function that lowers the door glass 150 mm (5.9 in.) when detected.
Encoder continues detecting the movement of front power window motor (driver side) and transmits to main power window and door lock/unlock switch as the encoder pulse signal while front power window motor (driver side) is operating.
Resistance is applied to the front power window motor (driver side) rotation that changes the frequency of encoder pulse signal if foreign material is trapped in the door glass.
Main power window and door lock/unlock switch controls to lower the window glass for 150 mm (5.9 in) after it detects encoder pulse signal frequency change.

OPERATION CONDITION

When front door glass (driver side) AUTO-UP operation is performed (anti-pinch function does not operate just before the door glass closes and is fully closed).

NOTE: Depending on environment and driving conditions, if a similar impact or load is applied to the door glass, it may lower.

Fail Safe

FAIL-SAFE CONTROL

Switches to fail-safe control when malfunction is detected in encoder signal that detects up/down speed and direction of door glass. Switches to fail-safe control when error beyond regulation value is detected between the fully closed position and the actual position of the glass.

Error	Error condition
Pulse sensor malfunction	When only one side of pulse signal is being detected for more than the specified value.
Both pulse sensors malfunction	When both pulse signals have not been detected for more than the specified value during glass open/close operation.
Pulse direction malfunction	When the pulse signal that is detected during glass open/close operation detects the opposite condition of power window motor operating direction.
Glass recognition position malfunction 1	When it detects the error between glass fully closed position in power window switch memory and actual fully closed position during glass open/close operation is more than the specified value.
Glass recognition position malfunction 2	When it detects pulse count more than the value of glass full stroke during glass open/close operation.

It changes to condition before initialization and the following functions do not operate when switched to failsafe control.

Auto-up operation
Anti-pinch function
Retained power function

Perform initial operation to recover when switched to fail-safe mode. However, it switches back to fail-safe control when malfunction is found in power window switch or in the motor.

Component parts

Component Parts Location A/C switch assembly View with front door finisher removed View with rear door finisher removed No. Component parts Function ...

Diagnosis system (BCM) (with intelligent key system)

COMMON ITEM COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT performs the following functions via CAN communication with BCM. Direct Diagnostic Mode De ...

Other materials:

Power steering
WARNING If the engine is not running or is turned off while driving, the power assist for the steering will not work. Steering will be harder to operate. When the power steering warning light illuminates with the engine running, there will be no power a ...

The parking brake release warning continues sounding, or does not sound
Description The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is released. The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking brake applied. Diagnosis Procedure 1. CHECK P ...

Brake booster
Inspection Operation Depress the brake pedal several times at five second intervals with the engine stopped. Start the engine with the brake pedal fully depressed. Check that the clearance between brake pedal and dash lower panel decreases. NOTE: A slight impact with a small click may be fe ...