Nissan Rogue Service Manual: Symptom diagnosis

Nissan Rogue Service Manual / Body exterior, doors, roof & vehicle security / Security Control System / With intelligent key system / Symptom diagnosis

ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE

Description

Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.

NOTE:

Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check each symptom.
The engine start function, door lock function, power distribution system, and NATS-NVIS in the Intelligent Key system are closely related to each other regarding control. The vehicle security function can operate only when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
“ENGINE START BY I-KEY” in “WORK SUPPORT” is ON when setting on CONSULT.
One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.

Diagnosis Procedure

1.PERFORM WORK SUPPORT

Perform “INSIDE ANT DIAGNOSIS” on "Work support" in “INTELLIGENT KEY”.

Refer to BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)".

>> GO TO 2.

2.PERFORM SELF-DIAGNOSTIC RESULT

Perform "Self-Diagnostic Result" in “BCM”, and check whether or not DTC of inside key antenna is detected.

Is DTC detected? YES >> Refer to BCS-48, "DTC Index".

NO >> GO TO 3.

3.CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.

Refer to SEC-80, "Component Inspection".

Is the operation normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning parts.

4.CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK

Description

Security indicator lamp does not blink when ignition switch is in a position other than ON

NOTE:

Before performing the diagnosis, check “Work Flow”. Refer to SEC-62, "Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check each symptom.

Conditions of Vehicle (Operating Conditions)

Ignition switch is not in the ON position.

Diagnosis Procedure

1.CHECK SECURITY INDICATOR LAMP

Check security indicator lamp.

Refer to SEC-102, "Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning parts.

2.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

VEHICLE SECURITY SYSTEM CANNOT BE SET INTELLIGENT KEY

INTELLIGENT KEY : Description

ARMED phase is not activated when door is locked using Intelligent Key.

NOTE: Check that vehicle is under the condition shown in Conditions of vehicle before starting diagnosis and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

Confirm the setting of "SECURITY ALARM SET" is "ON" in "WORK SUPPORT" mode of "THEFT ALM" of "BCM" using CONSULT.

INTELLIGENT KEY : Diagnosis Procedure

1.CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)

Lock/unlock door with Intelligent Key.

Refer to SEC-9, "INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION : System Description".

Is the inspection result normal? YES >> GO TO 2.

NO >> Check Intelligent Key system (remote keyless entry function).

2.CHECK HOOD SWITCH

Check hood swiwtch.

Refer to SEC-99, "Component Function Check" .

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace hood switch.

3.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

DOOR REQUEST SWITCH

DOOR REQUEST SWITCH : Description

ARMED phase is not activated when door is locked using door request switch.

NOTE: Check that vehicle is under the condition shown in Conditions of vehicle before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

Confirm the setting of SECURITY ALARM SET is ON in WORK SUPPORT mode of THEFT ALM of BCM using CONSULT.

DOOR REQUEST SWITCH : Diagnosis Procedure

1.CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)

Lock/unlock door with door request switch.

Refer to SEC-9, "INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION : System Description".

Is the inspection result normal? YES >> GO TO 2.

NO >> Check Intelligent Key system (door lock function).

2.CHECK HOOD SWITCH

Check hood switch.

Refer to SEC-99, "Component Function Check".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace hood switch.

3.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

DOOR KEY CYLINDER

DOOR KEY CYLINDER : Description

ARMED phase is not activated when door is locked using mechanical key.

NOTE: Check that vehicle is under the condition shown in Conditions of vehicle before starting diagnosis, and check each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

Confirm the setting of SECURITY ALARM SET is ON in WORK SUPPORT mode of THEFT ALM of BCM using CONSULT.

DOOR KEY CYLINDER : Diagnosis Procedure

1.CHECK POWER DOOR LOCK SYSTEM

Lock/unlock door with mechanical key.

Refer to SEC-14, "VEHICLE SECURITY SYSTEM : System Description".

Is the inspection result normal? YES >> GO TO 2.

NO >> Check power door lock system.

2.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

Description

Alarm does not operate when alarm operating condition is satisfied.

NOTE: Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis and check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

Confirm the setting of “SECURITY ALARM SET” is ON in “Work Support” mode of “THEFT ALM” of “BCM” using CONSULT.

Diagnosis Procedure

1.CHECK DOOR SWITCH

Check door switch.

Refer to DLK-149, "Component Function Check".

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace the malfunctioning door switch.

2.CHECK HOOD SWITCH

Check hood switch.

Refer to SEC-99, "Component Function Check".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace hood switch.

3.CHECK HORN FUNCTION

Check horn function.

Refer to SEC-101, "Component Function Check".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace the malfunctioning parts.

4.CHECK HEADLAMP FUNCTION

Check headlamp function.

Refer to SEC-98, "Component Function Check".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace the malfunctioning parts.

5.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

PANIC ALARM FUNCTION DOES NOT OPERATE

Description

NOTE:

Before performing the diagnosis following procedure, check “Work Flow”. Refer to SEC-62, "Work Flow".
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis and check each symptom.

CONDITIONS OF VEHICLE (OPERATION CONDITIONS)

Ignition switch is in OFF or LOCK position.
Intelligent Key is removed from key slot.

Diagnosis Procedure

1.CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.

Does door lock/unlock with Intelligent Key button? YES >> GO TO 2.

NO >> Go to DLK-176, "Diagnosis Procedure".

2.CHECK VEHICLE SECURITY ALARM OPERATION

Check vehicle security alarm operation.

Does alarm (headlamps and horns) active? YES >> GO TO 3.

NO >> Go to SEC-14, "VEHICLE SECURITY SYSTEM : System Description".

3.CHECK “PANIC ALARM SET” SETTING IN “WORK SUPPORT”

Check “PANIC ALARM SET” setting in “Work Support”.

Refer to BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)".

Is the inspection result normal? YES >> GO TO 4.

NO >> Set “PANIC ALARM SET” setting in “Work Support”.

4.CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal? YES >> Check intermittent incident. Refer to GI-41, "Intermittent Incident".

NO >> GO TO 1.

DTC/circuit diagnosis

P1610 LOCK MODE Description ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times or more while communication between ECM and BCM is not n ...

Removal and installation

NATS ANTENNA AMP. Exploded View Instrument finisher B Push button ignition switch NATS antenna amp. Pawl Removal and Installation REMOVAL Remove the instrument finisher ...

Other materials:

U1044 ENG comm circuit
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition U1044 ENG COMM CIRCUIT (Engine communication circuit A signal voltage of LIN communication between ECM and generator is excessively low or e ...

System
System Description When the vehicle has reached a speed of 40 km/h (25 MPH) or greater, the BCM receives a signal transmitted from the tire pressure sensors installed in each wheel. If the BCM detects low inflation pressure or a system malfunction, it sends a signal to the combination meter v ...

AM radio reception
AM signals, because of their low frequency, can bend around objects and skip along the ground. In addition, the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics, AM signals are also subject to interference as they travel from transmitter to r ...