Nissan Rogue manuals

Nissan Rogue Service Manual: Rear washer nozzle and tube

Nissan Rogue Service Manual / Driver controls / Wiper & Washer / Removal and installation / Rear washer nozzle and tube

Exploded View

Exploded View

  1. Rear washer tube
  2. Rear grommet

Clip

Removal and Installation - Rear Washer Nozzle

REMOVAL

  1.  Remove rear access panel. Refer to INT-38, "Exploded View".
  2. Release pawls and remove rear washer nozzle (1).

    : Pawl

Removal

INSTALLATION

Installation in the reverse order of removal.

Removal and Installation - Rear Washer Tube

REMOVAL

  1.  Remove engine side cover (RH). Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  2.  Release clips and remove front air spoiler.
  3.  Remove engine under cover. Refer to EXT-37, "ENGINE UNDER COVER : Removal and Installation".
  4.  Partially remove fender protector (RH). Refer to EXT-37, "ENGINE UNDER COVER : Removal and Installation".
  5.  Release seat latches by pulling straps (A) rearward, then lift seat from seat strikers (LH/RH).

Removal

  1. Remove dash side finisher (RH). Refer to INT-24, "DASH SIDE FINISHER : Removal and Installation".
  2.  Remove center pillar lower finisher (RH). Refer to INT-22, "CENTER PILLAR LOWER FINISHER : Removal and Installation".
  3.  Remove luggage rear plate. Refer to INT-37, "LUGGAGE REAR PLATE : Removal and Installation".
  4.  Remove luggage side upper finisher (LH/RH). Refer to INT-36, "LUGGAGE SIDE UPPER FINISHER : Removal and Installation".
  5.  Release rear clips and partially remove headliner. Refer to INT-29, "Exploded View".
  6.  Disconnect rear washer tube from washer tank and rear washer nozzle.
  7.  Release clips and remove rear washer tube.

INSTALLATION

Installation is in the reverse order of removal.

Inspection and Adjustment

INSPECTION

Check that air can pass through the nozzle by blowing into the nozzle and that air cannot flow in the opposite direction.

O: Air can go
X: Air cannot go

Inspection

ADJUSTMENT

If operating properly, spray positions should match the positions shown. If spray positions do not match, confirm the rear washer nozzle is properly seated and working properly. If the spray positions still do not match as shown, then replace the rear washer nozzle. Refer to WW-72, "Removal and Installation - Rear Washer Nozzle"

Adjustment

  1. Black print
  2. Wiping area
  3. Spray target area
  4.  12.8
  5. 12.8
  6. 25.7
  7.  15.6
  8.  20.6
Rear wiper motor
Exploded View Rear wiper motor Back door Rear wiper motor harness Removal and Installation REMOVAL  Remove rear wiper arm. Refer to WW-69, "Removal and Installation&quo ...

Service data and specifications (sds)
Specifications WINDSHIELD WASHER FLUID ...

Other materials:

BMW Digital Key
Principle BMW Digital Key allows the vehicle to be unlocked and locked, as well as started, with a compatible smartphone. General information The availability of the BMW Digital Key depends on the equipment and national-market version. BMW Digital Key can be used with a compatible smartphone or ot ...

Cargo cover
Safety information Warning Loose objects or devices with a cable connection to the vehicle, for instance mobile phones, can be thrown about the car's interior while driving, for instance in the event of an accident, braking or evasive maneuver. There is a risk of injury. Secure loose objects or devi ...

P0335 CKP sensor (POS)
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting conditio P0335 CKP SEN/CIRCUIT (Crankshaft position sensor ″A″ circuit) The crankshaft position sensor (POS) signal is not detected by ...

В© 2014-2022 Copyright www.nirogue.com