Nissan Rogue manuals

Nissan Rogue Service Manual: Preparation

Special Service Tools

The actual shapes of TechMate tools may differ from those of special service tools illustrated here.

Tool number (TechMate No.) Tool name Description
KV38100200 (J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
  • Installing drive pinion oil seal
  •  Installing side oil seal
ST27861000 ( — )
Drift
a: 62 mm (2.44 in) dia.
b: 52 mm (2.05 in) dia.
Installing drive pinion oil seal
ST35271000 (J-26091)
Drift
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing drive pinion oil seal
KV40100610 (J-26089)
Drift
a: 63 mm (2.48 in) dia.
b: 54.3 mm (2.138 in) dia.
  • Removing and installing gear carrier and rear cover (2 pieces are used)
  •  Installing pinion front bearing inner race
ST33052000 ( — )
Adaptor
a: 22 mm (0.87 in) dia.
b: 28 mm (1.10 in) dia.
Removing side bearing inner race
KV40105020 ( — )
Drift
a: 39.7 mm (1.563 in) dia.
b: 35 mm (1.38 in) dia.
c: 15 mm (0.59 in)
Installing side bearing inner race
KV38109500 ( — )
Drive pinion socket
  • Removing and installing drive pinion lock nut
  •  Measuring preload torque
KV38109400 ( — )
Pinion nut wrench
Removing and installing drive pinion lock nut
ST17130000 ( — )
Drift
a: 31.8 mm (1.252 in) dia.
b: 58 mm (2.28 in) dia.
Installing pinion rear bearing outer race
ST33230000 (J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.
Installing pinion front bearing outer race
ST23860000 ( — )
Drift
a: 38 mm (1.50 in) dia.
b: 33 mm (1.30 in) dia.
  • Installing pinion rear bearing inner race
  •  Installing pinion front bearing inner race
ST38220000 ( — )
Press stand
a: 63 mm (2.48 in) dia.
b: 65 mm (2.56 in)
Installing pinion front bearing inner race
ST3127S000 (J-25765-A) Preload gauge Measuring preload torque
KV381086S1 ( — )
Dummy cover set
1. KV38108610 ( — )
Dummy cover
2. KV38108621 ( — )
Dummy cover spacer
3. KV38108630 ( — )
Dummy cover shim
  • Checking backlash
  •  Checking drive gear runout
  •  Checking tooth contact

Commercial Service Tools

Tool name Description
Separator

  • Removing side bearing inner race
  •  Removing pinion rear bearing inner race
Puller
  • Removing side bearing inner race
  •  Removing pinion rear bearing inner race
Pin punch
a: 4.5 mm (0.177 in) dia.
Removing and installing lock pin
Oil seal remover Removing drive pinion oil seal
Power tool Loosening bolts and nuts
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONE ...

System description
STRUCTURE AND OPERATION Sectional View Drive gear Side bearing Differential case Pinion mate shaft Side gear Pinion mate gear Drive pinion Collapsible spacer AWD solenoi ...

Other materials:

Bluetooth® Hands-Free Phone System voice commands
To access the Bluetooth® Hands-Free Phone System voice commands:  Press the button.  Say “Call” and then a name in the vehicle phonebook to call that entry. Otherwise, say “Phone” to access various phone commands. If the Bluetooth® has been set to “Off”, the s ...

CAN system (type 2)
MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT Diagnosis Procedure 1.CHECK CONNECTOR  Turn the ignition switch OFF.  Disconnect the battery cable from the negative terminal.  Check the following terminals and connectors for damage, bend and loose connection (connector side an ...

Starting the engine (models with NISSAN Intelligent Key® system)
Apply the parking brake.  Move the shift lever to P (Park) or N (Neutral). P (Park) is recommended. The starter is designed not to operate if the shift lever is in any of the driving positions.  Push the ignition switch to the ON position. Depress the brake pedal and pus ...

© 2014-2024 Copyright www.nirogue.com