Nissan Rogue manuals

Nissan Rogue Service Manual: P2813 select solenoid

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition
P2813 SELECT SOLENOID (Select solenoid) When any of 1, or 2 is satisfied:
  1.  When all the following conditions are established three times in 1DC
  •  Precondition
  •  DTC other than the applicable DTC is not detected.
  •  Throttle position: More than 6.27 deg.
  •  Vehicle speed: Less than 3 km/h (1 MPH)
  •  CVT fluid temperature: More than 20°C (68°F)
  •  Selector lever: Other than P, N
  •  Turbine speed when performed N → D, N (P) → R: More than 500 rpm
  •  TCM power supply voltage: More than 11 V
  •  Detection time
  •  N → D: 0.4 seconds
  •  N → R: 0.3 seconds
  •  P → R: 0.3 seconds
  1.  When all of the following conditions are satisfied and this state is maintained for 30 seconds:
  •  The counting of time continues while all of the following conditions are satisfied and stops when the conditions become unsatisfied (the count is maintained). When accumulated time reaches 30 seconds (Clutch is judged as engaged and the count is reset.)
  •  Selector lever: Other than P, N
  •  Vehicle speed: Less than 3 km/h (1 MPH)
  •  Differences between primary pulley speed and secondary speed: Less than 120 rpm
  •  Clutch instructions pressure: 0.95 MPa or more
  •  Differences between turbine speed and input speed: Less than 200 rpm
  •  Turbine speed – speed: More than 450 rpm
  •  DTC other than the applicable DTC is not detected.
  •  TCM power supply voltage: More than 11 V

NOTE: DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF → ON → driving → OFF”.

POSSIBLE CAUSE

Select solenoid valve

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION 1

  1.  Start the engine.
  2.  Maintain the following conditions. (Keep 30seconds or more after the selector lever shifted.)

Selector lever : N→ D, N → R, P→ R

  1. Check the first trip DTC.

Is “P2813”detected? YES >> Go to TM-171, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

>>WORK END

P2765 input speed sensor B
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2765 INPUT SPEED SENSOR B (Input/Turbine Speed Sensor ...

P2814 select solenoid
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2814 SELECT SOLENOID (Select solenoid) When all of ...

Other materials:

P2815 select solenoid
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P2815 SELECT SOLENOID (Select solenoid) When all of the following conditions are satisfied and this state is maintained for 0.2 seconds: &nb ...

Troubleshooting guide
Verify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent Key is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom Possible Cause Remedy When stopping the engine The Shift to Pa ...

Available views
WARNING  The distance guide line and the vehicle width line should be used as a reference only when the vehicle is on a paved, level surface. The distance viewed on the monitor may be different than the actual distance between the vehicle and displayed objects ...

© 2014-2024 Copyright www.nirogue.com