Nissan Rogue manuals

Nissan Rogue Service Manual: P2138 APP sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P2138 APP SENSOR (Throttle/pedal position sensor/switch ″D″ / ″E″ voltage correlation) Rationally incorrect voltage is sent to ECM compared with the signals from APP sensor 1 and APP sensor 2.

POSSIBLE CAUSE

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and let it idle for 1 second.
  2.  Check DTC.

Is DTC detected? YES >> Proceed to EC-449, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.CHECK APP SENSOR 1 POWER SUPPLY

  1.  Turn ignition switch OFF.
  2. Disconnect accelerator pedal position (APP) sensor harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between APP sensor harness connector and ground.

Check APP sensor 1 power supply

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between APP sensor harness connector and ECM harness connector.

Check APP sensor 1 power supply circuit

  1. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

4.CHECK APP SENSOR 2 POWER SUPPLY

Check the voltage between APP sensor harness connector and ground.

Check APP sensor 2 power supply

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Perform EC-484, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

6.CHECK APP SENSOR GROUND CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between APP sensor harness connector and ECM harness connector.

Heck APP sensor ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK APP SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between APP sensor harness connector and ECM harness connector.

Check APP sensor input signal circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace error-detected parts

8.CHECK APP SENSOR

Check the APP sensor. Refer to EC-451, "Component Inspection".

Is the inspection result normal? YES >> GO TO 9.

NO >> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".

9.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK ACCELERATOR PEDAL POSITION SENSOR

  1.  Turn ignition switch OFF.
  2.  Reconnect all harness connectors disconnected.
  3.  Turn ignition switch ON.
  4.  Check the voltage between ECM harness connector terminals as per the following conditio

Check accelerator pedal position sensor

Is the inspection result normal?

YES >> INSPECTION END

NO >> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".

P2135 TP sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2135 TP SENSOR-B1 (Throttle/pedal position sensor ...

P2610 ECM internal timer
Description This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state of engine cooling at an engine start. ...

Other materials:

Basic inspection
COMPONENT INSPECTION Inspection AFTER A COLLISION WARNING: Inspect all seat belt assemblies including retractors and attaching hardware after any collision. NISSAN/INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and t ...

Removal and installation
FRONT CAMERA Exploded View Front grille  Front camera Removal and Installation REMOVAL  Remove the front grille. Refer to EXT-23, "Removal and Installation".  Remove screws and front camera. INSTALLATION Installation is in the reverse order of re ...

Air conditioner operation
Start the engine, turn the fan control dial to the desired position, and press the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function operates only when the engin ...

В© 2014-2022 Copyright www.nirogue.com