Nissan Rogue Service Manual: P2127, P2128 APP sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P2127, P2128 APP sensor

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P2127	APP SEN 2/CIRC (Throttle/pedal position sensor/switch ″E″ circuit low)	An excessively low voltage from the APP sensor 2 is sent to ECM.
P2128	APP SEN 2/CIRC (Throttle/pedal position sensor/switch ″E″ circuit high)	An excessively high voltage from the APP sensor 2 is sent to ECM.

POSSIBLE CAUSE

Harness or connectors (APP sensor 2 circuit is open or shorted.)
Accelerator pedal position sensor (APP sensor 2)
Sensor power supply 2 circuit

FAIL-SAFE

The ECM controls the electric throttle control actuator in regulating the throttle opening in order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. So, the acceleration will be poor.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

Start engine and let it idle for 1 second.
Check DTC.

Is DTC detected? YES >> Proceed to EC-443, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK APP SENSOR 2 POWER SUPPLY

Turn ignition switch OFF.
Disconnect accelerator pedal position (APP) sensor harness connector.
Turn ignition switch ON.
Check the voltage between APP sensor harness connector and ground.

Check APP sensor 2 power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Perform EC-484, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK APP SENSOR 2 GROUND CIRCUIT

Turn ignition switch OFF.
Disconnect ECM harness connector.
Check the continuity between APP sensor harness connector and ECM harness connector.

Check APP sensor 2 ground circuit

Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT

Check the continuity between APP sensor harness connector and ECM harness connector.

Check APP sensor 2 input signal circuit

Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace error-detected parts

5.CHECK APP SENSOR

Check the APP sensor. Refer to EC-444, "Component Inspection".

Is the inspection result normal? YES >> GO TO 6.

NO >> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".

6.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK ACCELERATOR PEDAL POSITION SENSOR

Turn ignition switch OFF.
Reconnect all harness connectors disconnected.
Turn ignition switch ON.
Check the voltage between ECM harness connector terminals as per the following cond

Check accelerator pedal position sensor

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace accelerator pedal assembly. Refer to ACC-3, "Removal and Installation".

P2122, P2123 APP sensor

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2122 APP SEN 1/CIRC (Throttle/pedal position sens ...

P2135 TP sensor

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2135 TP SENSOR-B1 (Throttle/pedal position sensor ...

Other materials:

2nd row bench seat adjustment
Outboard seats Forward and backward Pull the center of the bar 1 up and hold it while you slide the seat forward or backward to the desired position. Release the bar to lock the seat in position. Reclining To recline the seatback, pull up on the lever 2 and lean back. To bring the seatba ...

Basic inspection
DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2. 2.CONFIRM THE SYMPTOM Try t ...

System description
COMPONENT PARTS Component Parts Location No. Component Description 1 Push-button ignition switch1 Push-button ignition switch (push switch) is pressed (ON), and transmits status signal to BCM and IPDM E/R. Ignition switch2 Ignition ...