Nissan Rogue Service Manual: P2004 intake manifold runner control valve

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P2004 intake manifold runner control valve

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P2004	TUMBLE CONT/V (Intake manifold runner control stuck open bank 1)	The target angle of intake manifold runner control valve controlled by ECM and the input signal from intake manifold runner control valve position sensor is not in the normal range.

POSSIBLE CAUSE

Harness or connectors (Intake manifold runner control valve motor circuit is open or shorted.)
Intake manifold runner control valve motor
Intake manifold runner control valve is stuck

FAIL-SAFE

Traveling control mode (Engine output control)
Device fix mode

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above −7°C (19°F)

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

Turn ignition switch ON.
Select “DATA MONITOR” mode with CONSULT.
Make sure that “COOLAN TEMP/S” indicates between −7°C (19°F) to 60°C (140°F).
If not, cool engine down or warm engine up until “COOLAN TEMP/S” indicates between −7°C (19°F) to 60°C (140°F). Then go to the following steps.
Fully release accelerator pedal and wait at least 10 seconds.
Depress accelerator pedal and wait at least 10 seconds.
Check 1st trip DTC.

With GST

Following the procedure “With CONSULT” above.

Is 1st trip DTC detected? YES >> Proceed to EC-420, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR POWER SUPPLY

Turn ignition switch ON.
Check the voltage between ECM harness connector.

Check intake manifold runner control valve motor power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR POWER SUPPLY CIRCUIT

Turn ignition switch OFF.
Disconnect ECM harness connector.
Disconnect IPDM E/R harness connector.
Check the continuity between ECM harness connector and IPDM E/R harness connector.

Check intake manifold runner control valve motor power supply circuit

Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR OUTPUT SIGNAL CIRCUIT

Disconnect intake manifold runner control valve motor harness connector.
Check the continuity between intake manifold runner control valve motor harness connector and ECM harness connector.

Check intake manifold runner control valve motor output signal circuit

Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR

Check the intake manifold runner control valve motor. Refer to EC-421, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace intake manifold assembly. Refer to EM-26, "Removal and Installation".

5.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE

With CONSULT

Turn ignition switch ON.
Select “DATA MONITOR” mode with CONSULT.
Make sure that “COOLAN TEMP/S” indicates between −7°C (19°F) to 60°C (140°F).
If not, cool engine down or warm engine up until “COOLAN TEMP/S” indicates between −7°C (19°F) to 60°C (140°F). Then go to the following steps.
Fully release accelerator pedal and make sure that “TUMBLE POS SEN” indicates between 2.8 V to 4.1 V.
Depress accelerator pedal and make sure that “TUMBLE POS SEN” indicates between 0.2 V to 1.4 V.
Check 1st trip DTC.

With GST

Following the procedure “With CONSULT” above.

Is 1st trip DTC detected? YES >> Replace intake manifold assembly. Refer to EM-26, "Removal and Installation".

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE MOTOR

Turn ignition switch OFF.
Disconnect intake manifold runner control valve motor harness connector.
Check the resistance between intake manifold runner control valve motor terminals as per the following.

Check intake manifold runner control valve motor

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace intake manifold assembly. Refer to EM-26, "Removal and Installation".

P1805 brake switch

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P1805 BRAKE SW/CIRCUIT (BRAKE SW/CIRCUT) A stop ...

P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor

DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P2014 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifo ...

Other materials:

P050A, P050B, P050E cold start control
Description ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition. This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions. DTC Description DTC DETECTION LOGIC DTC No. CONSULT scre ...

Passenger side door mirror defogger
Description Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror from fogging up. Component Function Check 1.CHECK DOOR MIRROR DEFOGGER RH Check that the heating wire of door mirror defogger RH is heated when turning the rear window def ...

Preparation
Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description KV40107300 ( — ) Boot band crimping tool Installing boot band KV40107500 ( — ) Drive shaft attach ...