Nissan Rogue manuals

Nissan Rogue Service Manual: P1715 input speed sensor

Description

ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control.

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting conditio
P1715 IN PULY SPEED (IN PULY SPEED) Input speed sensor signal is different from the theoretical value calculated by ECM from output speed sensor signal and engine rpm signal.

POSSIBLE CAUSE

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and drive the vehicle at more than 50 km/h (31 MPH) for at least 5 seconds.

    CAUTION: Always drive vehicle at a safe speed.

  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-416, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P1715 is displayed with DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B, first perform the trouble diagnosis for DTC UXXXX, P0335, P0340, P0603, P0604, P0605, P606, P0607, P060A, or P060B.

Is applicable DTC detected?

YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK DTC WITH TCM

Check DTC with TCM. Refer to TM-47, "CONSULT Function".

Is the inspection result normal? YES >> GO TO 3.

NO >> Perform trouble shooting relevant to DTC indicated.

3.REPLACE TCM

Replace TCM. Refer to TM-202, "Removal and Installation".

>> INSPECTION END

P1574 ASCD vehicle speed sensor
Description The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combination meter, and the other is from TCM (Transmission control module). The ECM uses ...

P1805 brake switch
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P1805 BRAKE SW/CIRCUIT (BRAKE SW/CIRCUT) A stop ...

Other materials:

Jump-starting
General information If the battery is discharged, the engine can be started using the battery of another vehicle and two jumper cables. Only use jumper cables with fully insulated clamp handles. Safety information DANGER Contact with live components can lead to an electric shock. There is a risk of ...

Diagnosis system (ECM)
DIAGNOSIS DESCRIPTION DIAGNOSIS DESCRIPTION : 1st Trip Detection Logic and Two Trip Detection Logic When a malfunction is detected for the first time, 1st trip DTC and 1st trip Freeze Frame data are stored in the ECM memory. The MIL will not illuminate at this stage. <1st trip> If the ...

Hill descent control switch (if so equipped)
Hill descent control switch (if so equipped) WARNING  Never rely solely on the hill descent control system to control vehicle speed when driving on steep downhill grades. Always drive carefully when using the hill descent control system and decelerate the vehic ...

В© 2014-2022 Copyright www.nirogue.com