Nissan Rogue Service Manual: P1574 ASCD vehicle speed sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P1574 ASCD vehicle speed sensor

Description

The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combination meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD control. Refer to EC-47, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description" for ASCD functions.

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P1574	ASCD VHL SPD SEN (ASCD VHL SPD SEN)	ECM detects a difference between two vehicle speed signals is out of the specified range.

POSSIBLE CAUSE

Harness or connectors (CAN communication line is open or shorted.)
ABS actuator and electric unit (control unit)
TCM
ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P1574 is displayed with DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or P060B, first perform the trouble diagnosis for DTC U1001, P0500, P0603, P0604, P0605, P0606, P0607, P060A or P060B.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

Start engine.
Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION: Always drive vehicle at a safe speed.
NOTE: This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
Check DTC.

Is DTC detected? YES >> Proceed to EC-415, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK DTC WITH TCM

Check DTC with TCM. Refer to TM-47, "CONSULT Function".

Is DTC detected? NO >> GO TO 3.

YES >> Perform trouble shooting relevant to DTC indicated.

3.CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”

Check DTC with ABS actuator and electric unit (control unit). Refer to BRC-44, "CONSULT Function".

Is DTC detected? NO >> INSPECTION END

YES >> Perform trouble shooting relevant to DTC indicated.

P1572 brake pedal position switch

DTC Description DTC DETECTION LOGIC NOTE: This self-diagnosis has the one trip detection logic. When malfunction A is detected, DTC is not stored in ECM memory. And in that case, 1st trip DTC an ...

P1715 input speed sensor

Description ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control. DTC Description DTC DETECTION LOGIC DTC No. CONSUL ...

Other materials:

Battery
How to Handle Battery CAUTION: If it becomes necessary to start the engine with a booster battery and jumper cables, use a 12-volt booster battery. After connecting battery cables, ensure that they are tightly clamped to battery terminals for good contact. Never ...

Removal and installation
POWER SOCKET Removal and Installation FRONT POWER SOCKET Removal Remove cluster lid C. Refer to IP-21, "Removal and Installation". Release the pawls on the power socket and remove from the cluster lid C. Installation Installation is in the reverse order of remov ...

On board diagnostic (OBD) system
Diagnosis Description This system is an on board diagnostic system that records exhaust emission-related diagnostic information and detects a sensors/actuator-related malfunction. A malfunction is indicated by the malfunction indicator lamp (MIL) and stored in ECU memory as a DTC. The diagnos ...