Nissan Rogue manuals

Nissan Rogue Service Manual: P1078 EVT control position sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P1078 EXH TIM SEN/CIRC-B1 (EXH TIM SEN/CIRC-B1) An excessively high or low voltage from the sensor is sent to ECM.

POSSIBLE CAUSE

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and let it idle for 10 seconds.
  2.  Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-385, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK EXHAUST VALVE TIMING (EVT) CONTROL POSITION SENSOR POWER SUPPLY

  1.  Turn ignition switch OFF.
  2.  Disconnect exhaust valve timing (EVT) control position sensor harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between EVT control position sensor harness connector and ground.

Check exhaust valve timing (EVT) control position sensor power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Perform EC-484, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK EVT CONTROL POSITION SENSOR GROUND CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between EVT control position sensor harness connector and ECM harness connector.

Check EVT control position sensor ground circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK EVT CONTROL POSITION SENSOR INPUT SIGNAL CIRCUIT

  1.  Disconnect ECM harness connector.
  2.  Check the continuity between EVT control position sensor harness connector and ECM harness connector.

Check EVT control position sensor input signal circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace error-detected parts.

5.CHECK EVT CONTROL POSITION SENSOR

Check the EVT control position sensor. Refer to EC-387, "Component Inspection".

Is the inspection result normal? YES >> GO TO 6.

NO >> Replace EVT control position sensor. Refer to EM-64, "Exploded View".

6.CHECK CAMSHAFT (EXT)

Check the following.

Is the inspection result normal? YES >> GO TO 7.

NO >> Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to EM-64, "Removal and Installation".

Check camshaft (EXT)

7.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.EXHAUST VALVE TIMING (EVT) CONTROL POSITION SENSOR-1

  1.  Turn ignition switch OFF.
  2.  Disconnect EVT control position sensor harness connector.
  3.  Loosen the fixing bolt of the sensor.
  4.  Remove the sensor.
  5.  Visually check the sensor for chipping.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace EVT control position sensor. Refer to EM-64, "Exploded View".

Exhaust valve timing (EVT) control position sensor-1

2.EVT CONTROL POSITION SENSOR-2

Check resistance EVT control position sensor terminals as shown below.

EVT control position sensor-2

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace EVT control position sensor. Refer to EM-64, "Exploded View".

P0850 PNP switch
Description Transmission range switch is turn ON when the selector lever is P or N. ECM detects the position because the continuity of the line (the ON) exists. DTC Description DTC DETECTION LOG ...

P1148 closed loop control
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P1148 CLOSED LOOP-B1 (CLOSED LOOP-B1) The close ...

Other materials:

The parking brake release warning continues sounding, or does not sound
Description The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is released.  The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking brake applied. Diagnosis Procedure 1. CHECK P ...

Towing a trailer
WARNINGOverloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and performance and may lead to accidents.   CAUTION  Do not tow a trailer or haul a heavy load for the first 500 (805 km). Your engine, ...

C1199 brake booster
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1199 BRAKE BOOSTER When brake booster vacuum is approx. 0 kPa (0 mm- Hg) during engine running. Harness or connector  Vacuum sensor (brake booster) ...

В© 2014-2024 Copyright www.nirogue.com