Nissan Rogue manuals

Nissan Rogue Service Manual: P0746 pressure control solenoid A

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition
P0746 PC SOLENOID A (Pressure Control Solenoid A Performance/ Stuck Off) The detecting condition A or detection condition B is detected twice or more (1 second or more later after detection of the first) in the same DC under the following diagnosis conditions:
  •  Diagnosis conditions
  •  Engine speed: More than 600 rpm
  •  Primary pulley speed: More than 450 rpm
  •  Idle is not being detected.
  •  Acceleration/deceleration speed: −0.49 m/s2 (−0.05 G) or more
  •  The primary pulley speed experienced 300 rpm or more and the secondary pulley speed experienced 250 rpm or more at least once.
  •  Secondary pulley speed: More than 150 rpm
  •  TCM power supply voltage: More than 11 V
  •  Detection condition A
  • Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceeding 2.981 is 0.2 sec. or more continuously.
  • Detection condition B
  •  Status with the shifting ratio of the primary pulley speed/secondary pulley ratio exceeding 3.781 is 0.1 sec. or more continuously

NOTE: DC stands for "DRIVING CYCLE" and indicates a series of driving cycle of "Ignition switch OFF → ON → driving → OFF".

POSSIBLE CAUSE

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1.  Start the engine.
  2.  Drive the vehicle.
  3.  Maintain the following conditions for 10 seconds or more.

Selector lever : “D” position
Accelerator pedal position : 0.5/8 or more
Vehicle speed : 40 km/h (25 MPH) or more

  1. Stop the vehicle.
  2.  Check the first trip DTC.

Is “P0746”detected? YES >> Go to TM-138, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

>> WORK END

P0744 torque converter
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0744 TORQUE CONVERTER (Torque converter clutch circui ...

P0776 pressure control solenoid B
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content DTC detection condition P0776 PC SOLENOID B (Pressure Control Solenoid “B” ...

Other materials:

C1730, C1731, C1732, C1733 flat tire
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.  Activate and display TPMS sensor IDs  Display tire pressure reported by the TPMS sensor  Read TPMS DTC ...

Seatback pockets
Seatback pockets There is a pocket located on the back of the driver and passenger seats. These pockets can be used to store maps. WARNINGTo ensure proper operation of the passenger’s advanced air bag system, please observe the following items:  Do not allow a pas ...

Towing safety
Trailer hitch Your vehicle may be equipped with an optional trailer tow package. The trailer tow package includes a receiver-type frame mounted hitch. This hitch is rated for the maximum towing capacity of this vehicle when the proper towing equipment is used. Choose a proper ball mount and hi ...

© 2014-2024 Copyright www.nirogue.com