Nissan Rogue Service Manual: P0740 torque converter

Nissan Rogue Service Manual / Transmission & driveline / Transaxle & Transmission / Dtc/circuit diagnosis / P0740 torque converter

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0740	TORQUE CONVERTER (Torque Converter Clutch Circuit/Open)	When all of the following conditions are satisfied and this state is maintained for 5 seconds: TCM power supply voltage: More than 11 V P0743 is not detected. TCM judges that solenoid valve circuit is open.

POSSIBLE CAUSE

Harness or connector (Torque converter clutch solenoid valve circuit is open or shorted to power supply)
Torque converter clutch solenoid valve

FAIL-SAFE

Start is slow
Acceleration is slow
Lock-up is not performed

DTC CONFIRMATION PROCEDURE

CAUTION: Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PREPARATION BEFORE OPERATION

With CONSULT

Start the engine.
Select “Data Monitor” in “TRANSMISSION”.
Select “FLUID TEMP”.
Confirm that the CVT fluid temperature is in the following range.

FLUID TEMP : 20°C (68°F) or more

With GST

Start the engine.
Set the CVT fluid to 20°C (68°F) or more.

NOTE: When the ambient temperature is 20°C (68°F), the CVT fluid usually increases to 50 to 80°C (122 to 176°F) with driving in an urban area for approximately 10 minutes.

Is the CVT fluid 20°C (68°F) or more? YES >> GO TO 3.

NO >> 1. Warm the transaxle.

2. GO TO 3.

3.CHECK DTC DETECTION

Drive the vehicle.
Maintain the following conditions for 10 seconds or more.

Selector lever : “D” position
Vehicle speed : 40 km/h (25 MPH) or more

Stop the vehicle.
Check the first trip DTC.

Is “P0740” detected? YES >> Go to TM-132, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

Turn ignition switch OFF.
Disconnect TCM connector and CVT unit connector.
Check continuity between TCM harness connector terminal and CVT unit harness connector terminal.

Check circuit between TCM and CVT unit

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace malfunctioning parts.

2.CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check resistance between CVT unit harness connector terminal and ground.

Check circuit between CVT unit and ground

Is the inspection result normal? YES >> INSPECTION END

NO >> There is malfunction of torque converter clutch solenoid valve. Replace transaxle assembly. Refer to TM-220, "Removal and Installation".

P0717 input speed sensor A

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0717 INPUT SPEED SENSOR A (Input/Turbine Speed Sensor ...

P0743 torque converter

DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0743 TORQUE CONVERTER (Torque Converter Clutch Circui ...

Other materials:

Connector Information
HOW TO USE CONNECTOR INFORMATION Description Number Item Description 1 Connector number Alphabetic characters show to which harness the connector is placed. Numeric characters show the identification number of connectors. ...

P0606 ECM
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0606 CONTROL MODULE (Control module processor) Malfunction in ECM processor POSSIBLE CAUSE ECM FAIL-SAFE Not applicable DTC CONFIRMATION ...

Wiring diagram
POWER DOOR LOCK SYSTEM Wiring Diagram REMOTE KEYLESS ENTRY SYSTEM Wiring Diagram ...