DTC Description
DTC DETECTION LOGIC
DTC | CONSULT screen terms (Trouble diagnosis content) | DTC detection condition |
P0711 | FLUID TEMP SENSOR A (Transmission Fluid Temperature Sensor A Circuit Range/Performance) | When any of 1 or 2 is satisfied:
|
POSSIBLE CAUSE
CVT fluid temperature sensor
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
CAUTION: Always drive vehicle at a safe speed.
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.INSPECTION START
Is it necessary to erase permanent DTC? YES >> GO TO 3.
NO >> GO TO 7.
3.CHECK DTC (ECM AND TCM)
Check the DTC.
Is any DTC other than “P0711” detected? YES >> Check DTC detected item. Refer to EC-93, "DTC Index" (ECM), EC-93, "DTC Index" (TCM).
NO >> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE (PART 1)
TESTING CONDITION:
With CONSULT
NOTE: Cool the vehicle in an environment of ambient air temperature between −10°C (14°F) and 35°C (95°F).
CAUTION: Never turn ignition switch ON during this procedure.
NOTE: The vehicle must be cooled with the food open.
CAUTION: Never start the engine.
CAUTION: Never turn ignition switch OFF during idling.
With GST
NOTE: Cool the vehicle in an environment of ambient air temperature between −10°C (14°F) and 35°C (95°F).
CAUTION: Never turn ignition switch ON during this procedure.
NOTE: The vehicle must be cooled with the food open.
CAUTION: Never turn ignition switch OFF during idling.
Is “P0711” detected? YES >> Go to TM-119, "Diagnosis Procedure".
NO-1 (With CONSULT)>>GO TO 5.
NO-2 (With GST)>>GO TO 6.
5.CHECK CVT FLUID TEMPERATURE
With CONSULT
Is the value of “FLUID TEMP” 10°C (50°F) or more? YES >> INSPECTION END
NO >> GO TO 6.
6.PERFORM DTC CONFIRMATION PROCEDURE (PART 2)
With CONSULT
Selector lever : “D” position
Accelerator pedal position : 1.0/8 or more
Vehicle speed : 10 km/h (7 MPH) or more
With GST
Selector lever : “D” position
Accelerator pedal position : 1.0/8 or more
Vehicle speed : 10 km/h (7 MPH) or more
Is “P0711” detected? YES >> Go to TM-119, "Diagnosis Procedure".
NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
NO-2 >> Confirmation after repair: INSPECTION END
7.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
CAUTION: Never start the engine.
Selector lever : “D” position
Accelerator pedal position : 1.0/8 or more
Vehicle speed : 10 km/h (7 MPH) or more
With GST
Selector lever : “D” position
Accelerator pedal position : 1.0/8 or more
Vehicle speed : 10 km/h (7 MPH) or more
CAUTION: Never turn ignition switch OFF
Is “P0711” detected? YES >> Go to TM-119, "Diagnosis Procedure".
NO >> GO TO 8.
8.CHECK CVT FLUID TEMPERATURE SENSOR
Is the inspection result normal? YES-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".
YES-2 >> Confirmation after repair: INSPECTION END NO >> There is a malfunction of CVT fluid temperature sensor. Replace transaxle assembly. Refer to TM-220, "Removal and Installation".
Diagnosis Procedure
1.CHECK CVT FLUID TEMPERATURE SENSOR
Is the inspection result normal? YES >> GO TO 2.
NO >> GO TO 4.
2. CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 1)
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3. CHECK CIRCUIT BETWEEN TCM AND CVT UNIT (CVT FLUID TEMPERATURE SENSOR) (PART 2)
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Repair or replace damaged parts.
4. CHECK DTC (TCM)
With CONSULT
Is “P0711” detected? YES >> There is a malfunction of the CVT fluid temperature sensor. Replace the transaxle assembly.
Refer to TM-220, "Removal and Installation".
NO >> INSPECTION END
Periodic maintenance
IDLE SPEED
Inspection
1.CHECK IDLE SPEED
With CONSULT
Check idle speed in “DATA MONITOR” mode of “ENGINE” using CONSULT.
With GST
Check idle speed with Service $01 of GST.
>> INSPECTION END
IGNITION TIMING
Inspection
1.CHECK IGNITION TIMING
Attach timing light (A) to th ...
Operating tips
When the engine coolant temperature and
outside air temperature are low, the air flow
from the foot outlets may not operate for a
maximum of 150 seconds. However, this is
not a malfunction. After the coolant temperature
warms up, air flow from the foot outlets
will operate normally.
...
Power window and door lock/unlock switch RH
Removal and Installation
REMOVAL
Remove the front door pull handle bracket (RH). Refer to INT-15,
"Removal and Installation".
Release pawls using a suitable tool (A) and remove front door
power window and door lock/unlock switch finisher (RH) (1).
: Pawl
D ...