Nissan Rogue manuals

Nissan Rogue Service Manual: P0705 transmission range sensor A

DTC Description

DTC DETECTION LOGIC

DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition
P0705 T/M RANGE SENSOR A [Transmission Range Sensor A Circuit (PRNDL Input)] When all of the following conditions are satisfied and this state is maintained for 2 seconds:
  •  Two or more range signals simultaneously stay ON continuously
  •  TCM power supply voltage: More than 11 V

POSSIBLE CAUSE

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1.  Turn ignition switch ON.
  2.  Shift the selector lever through entire positions from “P” to “L”. (Hold the selector lever at each position for 5 seconds or more.)
  3.  Check the first trip DTC.

Is “P0705” detected? YES >> Go to TM-107, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: Refer to GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.CHECK TCM INPUT SIGNALS

With CONSULT

  1.  Turn ignition switch ON.
  2.  Select “Data Monitor” in “TRANSMISSION”.
  3.  Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, “P POSITION SW” and “L RANGE SW”.
  4.  Shift the selector lever through entire positions from “P” to “L” and check ON/OFF of each monitor item.

Check tcm input signals

Check tcm input signalsv

Without CONSULT

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Turn ignition switch ON.
  4.  Shift the selector lever from “P” to “L” and check voltage between TCM harness connector terminals and ground.

Check tcm input signals

Is the inspection result normal? YES >> INSPECTION END

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power voltage.)]>>GO TO 2.

NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power voltage.)]>>GO TO 4.

NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power voltage.)]>>GO TO 6.

NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power voltage.)]>>GO TO 8.

NO-5 [“L POSITION SW” is “ON” when selector is not in “L” position. (Or connector terminal 2 is at power voltage.)]>>GO TO 10.

2.CHECK D POSITION SW CIRCUIT (PART 1)

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Check continuity between TCM harness connector terminals.

Check D position sw circuit (part 1)

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts.

3.CHECK D POSITION SW CIRCUIT (PART 2)

  1.  Disconnect transmission range switch connector.
  2.  Turn ignition switch ON.
  3.  Check voltage between TCM harness connector terminal and ground.

Check D position sw circuit (part 2)

Is the inspection result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

4.CHECK N POSITION SW CIRCUIT (PART 1)

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Check continuity between TCM harness connector terminals.

Check N position sw circuit (part 1)

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.CHECK N POSITION SW CIRCUIT (PART 2)

  1.  Disconnect transmission range switch connector.
  2.  Turn ignition switch ON.
  3.  Check voltage between TCM harness connector terminal and ground.

Check N position sw circuit (part 2)

Is the inspection result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

6.CHECK P POSITION SW CIRCUIT (PART 1)

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Check continuity between TCM harness connector terminals.

Check P position sw circuit (part 1)

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace malfunctioning parts.

7.CHECK P POSITION SW CIRCUIT (PART 2)

  1.  Disconnect transmission range switch connector.
  2.  Turn ignition switch ON.
  3.  Check voltage between TCM harness connector terminal and ground.

Check P position sw circuit (part 2)

Is the inspection result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

8.CHECK R POSITION SW CIRCUIT (PART1)

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Check continuity between TCM harness connector terminals.

Check R position sw circuit (part1)

Is the inspection result normal? YES >> GO TO 9.

NO >> Repair or replace malfunctioning parts.

9.CHECK R POSITION SW CIRCUIT (PART 2)

  1.  Disconnect transmission range switch connector.
  2.  Turn ignition switch ON.
  3.  Check voltage between TCM harness connector terminal and ground.

Check R position sw circuit (part2)

Is the inspection result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

10.CHECK L POSITION SWITCH CIRCUIT (PART 1)

  1.  Turn ignition switch OFF.
  2.  Disconnect TCM connector.
  3.  Check continuity between TCM harness connector terminals.

Check L position switch circuit (part 1)

Is the inspection result normal? YES >> GO TO 11.

NO >> Repair or replace malfunctioning parts.

11.CHECK L POSITION SWITCH CIRCUIT (PART 2)

  1.  Disconnect transmission range switch connector.
  2.  Turn ignition switch ON.
  3.  Check voltage between TCM harness connector terminal and ground.

Check L position switch circuit (part 2)

Is the inspection result normal? YES >> GO TO 12.

NO >> Repair or replace malfunctioning parts.

12.CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to TM-111, "Component Inspection".

Is the check result normal? YES >> INSPECTION END

NO >> Repair or replace malfunctioning parts.

Component Inspection

1.CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Check transmission range switch

Check transmission range switch

Is the inspection result normal? YES >> INSPECTION END

NO >> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to TM- 205, "Removal and Installation".

P062F EEPROM
Description TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated value does not agree with the stored value, TCM judges this as a malfunction. ...

P0706 transmission range sensor A
DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0706 T/M RANGE SENSOR A (Transmission Range Sensor A ...

Other materials:

Preparation
Special Service Tools The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name Description — (165-GR8-1200KIT-NI) Multitasking battery and electrical diagnostic station Testing batteries, start ...

Wiring diagram
NAVIGATION WITH BOSE Wiring Diagram ...

Steering wheel turning force is heavy or light
Description Steering wheel turning force is heavy or light. Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS With CONSULT  Turn the ignition switch OFF to ON.  Perform “EPS” self-diagnosis. Is any DTC detected? YES >> Check the DTC. Refer to STC-13, "DTC Index" ...

© 2014-2024 Copyright www.nirogue.com