Nissan Rogue Service Manual: P0507 ISC system

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P0507 ISC system

Description

The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects the actual engine speed and sends a signal to the ECM.

The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.

The optimum value stored in the ECM is determined by taking into consideration various engine conditions, such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan operation, etc.).

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P0507	ISC SYSTEM (Idle air control system RPM higher than expected)	The idle speed is more than the target idle speed by 200 rpm or more.

POSSIBLE CAUSE

Electric throttle control actuator
Intake air leak
PCV system

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

If the target idle speed is out of the specified value, perform EC-141, "Work Procedure", before conducting DTC Confirmation Procedure.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
Always perform the test at a temperature above −10°C (14°F).

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

Start engine and warm it up to normal operating temperature.
Turn ignition switch OFF and wait at least 10 seconds.
Start engine and run it for at least 1 minute at idle speed.
Check 1st trip DTC.

Is 1st trip DTC detected?

YES >> Proceed to EC-355, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK PCV HOSE CONNECTION

Confirm that PCV hose is connected correctly.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK INTAKE AIR LEAK

Start engine and let it idle.
Listen for an intake air leak after the mass air flow sensor.

Is intake air leak detected? YES >> Discover air leak location and repair.

NO >> Replace ECM. Refer to EC-499, "Removal and Installation".

P0506 ISC system

Description The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let into the intake manifold, by operating the electric throttle control ac ...

P050A, P050B, P050E cold start control

Description ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition. This control promotes the activation of three way catalyst by heating the c ...

Other materials:

Heater and Air Conditioner (manual) (if so equipped)
Heater and Air Conditioner Fan speed control / system OFF dial / air conditioning (A/C) button Air flow control buttons Temperature control dial / MAX A/C button Air recirculation button Rear window and outside mirror (if so equipped) defroster but ...

The low washer fluid warning continues displaying, or does not display
Description The warning is still displayed even after washer fluid is added. The warning is not displayed even though the washer tank is empty. Diagnosis Procedure 1.CHECK WASHER FLUID LEVEL SWITCH SIGNAL CIRCUIT Check the washer fluid level switch signal circuit. Refer to MWI-71, " ...

P0011 IVT control
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0011 INT/V TIM CONT-B1 (″A″ Camshaft position - timing over-advanced or system performance bank 1) There is a gap between angle of ...