Nissan Rogue Service Manual: P0460 fuel level sensor

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / P0460 fuel level sensor

DTC Description

DTC DETECTION LOGIC

When the vehicle is parked, naturally the fuel level in the fuel tank is stable. It means that output signal of the fuel level sensor does not change. If ECM senses sloshing signal from the sensor, fuel level sensor malfunction is detected.

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detecting condition
P0460	FUEL LEV SEN SLOSH (Fuel Level Sensor ″A″ Circuit)	Even though the vehicle is parked, a signal being varied is sent from the fuel level sensor to ECM.

POSSIBLE CAUSE

Harness or connectors (The CAN communication line is open or shorted.)
Harness or connectors (The sensor circuit is open or shorted.)
Combination meter
Fuel level sensor

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P0460 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

Turn ignition switch OFF and wait at least 10 seconds.
Turn ignition switch ON.
Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

Start engine and wait maximum of 2 consecutive minutes.
Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-344, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P0460 is displayed with DTC UXXXX or P0607, first perform the trouble diagnosis for DTC UXXXX or P0607.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-93, "DTC Index".

NO >> GO TO 2.

2.CHECK COMBINATION METER FUNCTION

Refer to MWI-21, "CONSULT Function (METER/M&A)".

Is the inspection result normal? YES >> GO TO 3.

NO >> Refer to MWI-62, "Component Function Check".

3.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

P0456 EVAP control system

DTC Description DTC DETECTION LOGIC This diagnosis detects leaks in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve, using the negative pressure caused by de ...

P0461 fuel level sensor

DTC Description DTC DETECTION LOGIC Driving long distances naturally affect fuel gauge level. This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distanc ...

Other materials:

SRS air bag warning lamp does not turn on
AIR BAG Warning Lamp Does Not Turn On 1.CHECK METER FUSE Check the 10A fuse [No. 13, located in the fuse block (J/B)]. Is the fuse blown? YES >> GO TO 2. NO >> GO TO 3. 2.REPLACE METER FUSE AND CHECK AGAIN Replace 10A fuse [No. 13, located in the fuse block (J/B)] and turn ign ...

Instrument lower panel LH
Removal and Installation REMOVAL Release instrument side finisher (LH) (1) pawls using a suitable tool and remove. : Pawl Remove bolts (A) and fuel filler lid/hood lock release handle (1) from instrument lower panel LH. Remove data link cover from the instrument lowe ...

Cylinder head
Exploded View Cylinder head Cylinder head gasket Refer to INSTALLATION Removal and Installation REMOVAL Remove the timing chain. Refer to EM-45, "Removal and Installation". Remove the camshafts. Refer to EM-64, "Exploded View". & ...