Nissan Rogue manuals

Nissan Rogue Service Manual: P0127 IAT sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P0127 IAT SENSOR-B1 (Intake air temperature too high) Rationally incorrect voltage from the sensor is sent to ECM, compared with the voltage signal from engine coolant temperature sensor.

POSSIBLE CAUSE

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1.  Wait until engine coolant temperature is less than 96°C (205°F)

NOTE: Perform the following steps before engine coolant temperature is above 96°C (205°F).

  1.  Turn ignition switch ON.
  2.  Select “DATA MONITOR” mode of “ENGINE” using CONSULT
  3.  Start engine.
  4.  Hold vehicle speed at more than 70 km/h (43 MPH) for 100 consecutive seconds.

    CAUTION: Always drive vehicle at a safe speed.

  5.  Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected? YES >> Proceed to EC-221, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-24, "Exploded View".

2.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK INTAKE AIR TEMPERATURE SENSOR

  1.  Turn ignition switch OFF.
  2.  Disconnect mass air flow sensor harness connector and reconnect it again.
  3.  Turn ignition switch ON.
  4.  Select “DATA MONITOR” mode with CONSULT.
  5.  Check that “INT/A TEMP SEN” indicates as per following condition.
Monitor item Condition Value (Approx.)
INT/A TEMP SEN Temperature [°C (°F)] 25 (77) 1.9 - 2.1 (V)

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace mass air flow sensor (with intake air temperature sensor). Refer to EM-24, "Exploded View".

P0125 ECT sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0125 ECT SENSOR (Insufficient coolant temperature ...

P0128 thermostat function
DTC Description DTC DETECTION LOGIC Engine coolant temperature has not risen enough to open the thermostat even though the engine has run long enough. This is due to a leak in the seal or the ...

Other materials:

Periodic maintenance
FRONT WHEEL HUB AND KNUCKLE Inspection Move the wheel hub and bearing in an axial direction by hand to verify that looseness of wheel hub and bearing exists. If any looseness exists, replace the wheel hub and bearing. Axial end play : Refer to FAX-32, "Wheel Bearing". Rota ...

Diagnosis and repair work flow
Work Flow DETAILED FLOW 1.INTERVIEW FROM THE CUSTOMER Clarify customer complaints before inspection. First of all, perform an interview utilizing BRC-67, "Diagnostic Work Sheet" and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints careful ...

Heated seat switch
Exploded View Center console cup holder Driver heated seat switch  Passenger heated seat switch Switch carrier Pawl Removal and Installation REMOVAL  Remove the center console cup holder. Refer to IP-18, "Exploded View".  Remove screws fro ...

© 2014-2025 Copyright www.nirogue.com