Nissan Rogue manuals

Nissan Rogue Service Manual: P0122, P0123 TP sensor

DTC Description

DTC DETECTION LOGIC

DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition
P0122 TP SEN 2/CIRC-B1 (Throttle/pedal position sensor/switch ″A″ circuit low) An excessively low voltage from the TP sensor 2 is sent to ECM.
P0123 TP SEN 2/CIRC-B1 (Throttle/pedal position sensor/switch ″A″ circuit high) An excessively high voltage from the TP sensor 2 is sent to ECM.

POSSIBLE CAUSE

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.CHECK DTC PRIORITY

If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1.  Turn ignition switch OFF and wait at least 10 seconds.
  2.  Turn ignition switch ON.
  3.  Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 8 V at idle. >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

  1.  Start engine and let it idle for 1 second.
  2.  Check DTC.

Is DTC detected? YES >> Proceed to EC-216, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK DTC PRIORITY

If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643.

Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-379, "DTC Description".

NO >> GO TO 2.

2.CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY

  1.  Turn ignition switch OFF.
  2.  Disconnect electric throttle control actuator harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between electric throttle control actuator harness connector and ground.

Check throttle position sensor 2 power supply

Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between electric throttle control actuator harness connector and ECM harness connector

Check throttle position sensor 2 power supply circuit

  1. Also check harness for short to power.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

4.CHECK THROTTLE POSITION SENSOR 2 GROUND CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Check the continuity between electric throttle control actuator harness connector and ECM harness connector

Check throttle position sensor 2 ground circuit

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace error-detected parts.

5.CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT

  1.  Check the continuity between electric throttle control actuator harness connector and ECM harness connector.

Check throttle position sensor 2 input signal circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK THROTTLE POSITION SENSOR

Check the throttle position sensor. Refer to EC-218, "Component Inspection".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace electric throttle control actuator. Refer to EM-26, "Removal and Installation".

7.CHECK INTERMITTENT INCIDENT

Refer to GI-41, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK THROTTLE POSITION SENSOR

  1.  Turn ignition switch OFF.
  2.  Reconnect all harness connectors disconnected.
  3.  Perform “ Throttle Valve Closed Position Learning”. Refer to EC-140, "Work Procedure".
  4.  Turn ignition switch ON.
  5. Set selector lever to D position.
  6.  Check the voltage between ECM harness connector terminals as per the following conditions.

Check throttle position sensor

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace electric throttle control actuator. Refer to EM-26, "Removal and Installation".

P0117, P0118 ECT sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0117 ECT SEN/CIRC (Engine coolant temperature sen ...

P0125 ECT sensor
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition P0125 ECT SENSOR (Insufficient coolant temperature ...

Other materials:

Low tire pressure warning lamp
Component Function Check 1.CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second, when the ignition switch is turned ON. Is the inspection result normal? YES >> Inspection ...

Unbalance steering wheel turning force (torque variation)
Description Unbalance steering wheel turning force (torque variation). Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS With CONSULT  Turn the ignition switch OFF to ON.  Perform “EPS” self-diagnosis. Is any DTC detected? YES >> Check the DTC. Refer to STC-13, "DTC ...

C1704, C1705, C1706, C1707 low tire pressure
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.  Activate and display TPMS sensor IDs  Display tire pressure reported by the TPMS sensor  Read TPMS DTC ...

© 2014-2024 Copyright www.nirogue.com