DTC Description
DTC DETECTION LOGIC
DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting condition |
P0011 | INT/V TIM CONT-B1 (″A″ Camshaft position - timing over-advanced or system performance bank 1) | There is a gap between angle of target and phase-control angle degree. |
POSSIBLE CAUSE
FAIL-SAFE
DTC CONFIRMATION PROCEDURE
1.CHECK DTC PRIORITY
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-191, "DTC Description".
NO >> GO TO 2.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is between 11 V and 16 V at idle. >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected? YES >> Proceed to EC-178, "Diagnosis Procedure".
NO >> GO TO 4.
4.PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
CAUTION: Always drive at a safe speed.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected? YES >> Proceed to EC-178, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK DTC PRIORITY
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075.
Is applicable DTC detected? YES >> Perform diagnosis of applicable. Refer to EC-191, "DTC Description".
NO >> GO TO 2.
2.CHECK OIL PRESSURE WARNING LAMP
Is oil pressure warning lamp illuminated? YES >> Check the engine oil level. Refer to LU-7, "Inspection".
NO >> GO TO 3.
3.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Check the intake valve timing control solenoid valve. Refer to EC-179, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace intake valve timing control solenoid valve. Refer to EM-44, "Exploded View"
4.CHECK CRANKSHAFT POSITION SENSOR (POS)
Check the crankshaft position sensor (POS). Refer to EC-297, "Component Inspection (Crankshaft Position sensor)".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace crankshaft position sensor (POS). Refer to EM-92, "Exploded View".
5.CHECK CAMSHAFT POSITION SENSOR (PHASE)
Check the camshaft position sensor (PHASE). Refer to EC-300, "Component Inspection (Camshaft position sensor)".
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace camshaft position sensor (PHASE). Refer to EM-64, "Exploded View".
6.CHECK CAMSHAFT (INT)
Check the following.
Is the inspection result normal? YES >> GO TO 7.
NO >> Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to EM-64, "Removal and Installation".
7.CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned? YES >> Check timing chain installation. Refer to EM-45, "Removal and Installation".
NO >> GO TO 8.
8.CHECK LUBRICATION CIRCUIT
Refer to LU-7, "Inspection", “INSPECTION AFTER INSTALLATION”.
Is the inspection result normal? YES >> GO TO 9.
NO >> Clean lubrication line.
9.CHECK INTERMITTENT INCIDENT
Refer to GI-41, "Intermittent Incident".
>> INSPECTION END
Component Inspection
1.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-1
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace intake valve timing control solenoid valve. Refer to EM-44, "Exploded View".
2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-2
CAUTION: Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve timing control solenoid valve.
NOTE: Always replace O-ring when intake valve timing control solenoid valve is removed.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace intake valve timing control solenoid valve. Refer to EM-44, "Exploded View".
Warning systems switch (if so equipped)
Warning systems switch (if so equipped)
The warning systems switch is used to turn on
and off the warning systems (Lane Departure
Warning (LDW), Forward Collision Warning
(FCW) and Blind SpotWarning (BSW) systems)
that are activated using the settings menu on the
vehicle information displa ...
Windshield-washer fluid
Windshield-washer fluid reservoir
Fill the windshield-washer fluid reservoir periodically.
Add windshield-washer fluid when the low
windshield-washer fluid warning light comes on.
To fill the windshield-washer fluid reservoir, lift
the cap off the reservoir and pour the windshieldwasher ...
Rear wiper motor circuit
Component Function Check
1. CHECK REAR WIPER ON OPERATION
CONSULT ACTIVE TEST
Select "RR WIPER" of BCM active test item.
While operating the test item, check rear wiper operation.
ON : Rear wiper ON operation
OFF : Stop the rear wiper.
Is rear wiper operation norm ...