Nissan Rogue Service Manual: Moonroof unit assembly
Inspection
WIND DEFLECTOR
- Open glass lid fully.
- Visually check for proper installation, damaged/deteriorated components,
or foreign objects within mechanism.
Correct as required for smooth operation.
- Check for grease at the wind deflector arm (1) and pivot areas. If
necessary, apply a sufficient amount of grease for non-binding
operation.
Front
- Check that the wind deflector (1) moves freely within the moonroof
unit assembly while manually pressing down and releasing.
If a malfunction is detected, remove the moonroof unit assembly
and visually inspect. If damage is found, replace either wind
deflector (1) or moonroof unit assembly as required. Refer to
RF-63, "Removal and Installation" (WIND DEFLECTOR) or RF-
59, "Removal and Installation" (MOONROOF UNIT ASSEMBLY).
Front
LINK AND WIRE ASSEMBLY
NOTE:
Before replacing a suspect part, make sure it is the source of noise being
experienced.
- Check link to determine if coating film has peeled off excessively
enough that substrate is visible. Check
also to determine if link is the source of noise. Replace as necessary.
- Visually check to determine if a sufficient amount of grease has been
applied to wire or rail groove. If not,
add grease as required.
- Check wire for any damage or deterioration. If any damage is found,
replace moonroof unit assembly.
Refer to RF-59, "Removal and Installation"
WEATHERSTRIP
- Visually check weatherstrip for damage, deterioration, or deformation.
- Check for leaks around glass lid.
- Close glass lid.
- Pour water around surface to determine area of concern.
- For gaps or misalignment, adjust glass lid to specifications. Refer to
ADJUSTMENT in this section.
- For damaged sealing surfaces, either replace glass lid, refer to RF-49,
"Removal and Installation" or
repair the panel.
DRAIN HOSES
- Front pillar
- Moonroof unit assembly
- Rear pillar
- Rear drain hoses (LH/RH)
- Front drain hoses (LH/RH)
- Remove the headlining. Refer toINT-30, "Removal and
Installation".
- From the inside front pillar (3) visually check drain hoses (1) for:
- Proper connection at moonroof unit assembly (4) and drain
hose connection at the exit base (2).
- Damage, pinch, cracks, deterioration.
Front
- Pour water through drain hoses to determine watertight performance.
If damaged or leaking portions in any drain hose is found, replace entire
drain hose as necessary.
- From the inside of the rear quarter panel (1) visually check drain
hoses (2) for damage, pinching, cracks, or deterioration.
- Check for proper connection at moonroof unit assembly (3) and
drain hose (2) and for proper routing along the rear inner quarter
panel (1).
Front
ADJUSTMENT
CAUTION:
- Always work with a helper.
- Handle glass lid with care to prevent damage.
NOTE:
- For easier and more accurate installation, always mark each point
before removal.
- After any adjustment, check moonroof operation and glass lid
alignment.
- Roof panel
- Weatherstrip
- Glass lid/panoramic roof glass
Front
Gap adjustment (Front and Rear)
- Open sunshade (1).
: Front
- Tilt glass lid up, then release side trim cover (2) on each side
and set aside.
NOTE:
LH side shown; RH similar.
- Loosen glass lid bolts (A) (two each on LH and RH side), then tilt
glass lid down.
- Manually adjust glass lid from outside of vehicle until gaps A-A
and C-C are within specification.
NOTE:
Temporarily loosely tighten glass lid bolts to prevent movement between each
adjustment.
- Tilt glass lid up and down several times using moonroof switch to check
that it operates smoothly.
- Tilt glass lid up and tighten bolts.
NOTE:
First tighten left front bolt, then right rear bolt on glass lid to prevent
uneven torque while tightening
remaining bolts.
- Attach side trim covers (LH/RH), then tilt glass lid down.
Gap Adjustment (Sides)
The moonroof unit assembly is mounted on locator pins and adjustment from
side to side cannot be performed.
Surface Height Adjustment
- Tilt glass lid up and down several times using moonroof switch to check
that it operates smoothly.
- Check height difference between roof surface and glass lid surface,
then compare to specifications.
- If necessary, adjust height difference by using the following
procedure.
- Loosen glass lid bolts.
- Manually raise/lower glass lid until height difference is within
specification.
NOTE:
If necessary, shims may be added between moonroof unit assembly and roof to
increase adjustment
range. Refer to RF-49, "Removal and Installation".
Temporarily loosely tighten moonroof unit assembly bolts to prevent movement
between each adjustment.
Exploded View
- Panoramic roof glass
- Glass lid
- Side trim covers (LH/RH)
- Front drain hose (LH/RH)
- Moonroof motor assembly
- Sunshade motor assembly
- Moonroof front bracket (LH/RH)
- Moonroof rear bracket (LH/RH)
- Rear drain hose (LH/RH)
- Moonroof unit assembly
- Rear trim covers (LH/RH)
Front
Removal and Installation
REMOVAL
CAUTION:
- Always work with a helper.
- When taking moonroof unit assembly out, use cloths to protect the
seats and trim from damage.
- Remove headlining. Refer to INT-30, "Removal and Installation".
- Disconnect drain hoses (front/rear) from moonroof unit assembly. Refer
to RF-55, "Inspection".
- Disconnect harness connectors from moonroof motor assembly and sunshade
motor assembly.
- Remove nuts, then using a helper carefully lift each side and remove
moonroof unit assembly out back of
vehicle.
WARNING:
Bodily injury may occur if moonroof unit assembly is not supported properly when
removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing the moonroof unit assembly, perform the leak test and check
that there is no air or
water intrusion. Refer to RF-55, "Inspection".
Exploded View
Panoramic roof glass
Glass lid
Side trim covers (LH/RH)
Front drain hose front (LH/RH)
Moonroof motor assembly
Sunshade motor assembly
Moonroof front bracke ...
Removal and Installation
REMOVAL
Remove the moonroof unit assembly. Refer to RF-53, "Removal and
Installation".
Place the moonroof unit assembly (1) on a flat surface upside
down ...
Other materials:
Inspection and adjustment
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
When replacing the occupant classification system control unit, perform
zero point reset procedure. Refer to
SRC-42, "ZERO POINT RESET : Special Repair Requirement".
When ...
U0073 communication bus a OFF
DTC Description
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
U0073
COMM BUS A OFF
(Control Module Communication Bus A Off)
TCM communication blockage lasts for 2 seconds or more when turning
ON the ignition sw ...
Water hose
Exploded View
Water outlet
Hose clamp
Water hose A
Clip
CVT oil warmer
Transaxle assembly
Water hose B
Heater thermostat
Water hose C
: Always replace after every
disassembly.
: N·m (kg-m, ft-lb)
Removal and Installation
REMOVAL
WARNING:
Do not remove the rad ...
© 2014-2024 Copyright www.nirogue.com