Nissan Rogue manuals

Nissan Rogue Service Manual: Interior room lamp control circuit

Description

Controls each interior room lamp (ground side) by PWM signal.

NOTE: PWM signal control period is approximately 250 Hz (in the gradual brightening/dimming).

Component Function Check

CAUTION: Before performing the diagnosis, check that the following is normal.

1.CHECK INTERIOR ROOM LAMP CONTROL FUNCTION

CONSULT ACTIVE TEST

  1.  Switch the map lamp switch and room lamp switch to DOOR.
  2.  Turn power switch ON.
  3.  Select “INT LAMP” of “BCM” active test item.
  4.  With operating the test items, check that each interior room lamp turns ON/OFF (gradual brightening/dimming).

On : Interior room lamp gradual brightening
Off : Interior room lamp gradual dimming

Does the interior room lamp turns ON/OFF (gradual brightening/dimming)? YES >> Interior room lamp control circuit is normal.

NO >> Refer to INL-49, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK INTERIOR ROOM LAMP CONTROL OUTPUT

CONSULT ACTIVE TEST

  1.  Turn power switch OFF.
  2.  Remove all the bulbs of map lamp and room lamp.
  3.  Turn power switch ON.
  4.  Select “INT LAMP” of “BCM” active test item.
  5.  With operating the test item, check continuity between BCM harness connector and ground.

Check interior room lamp control output

Is the inspection result normal? YES >> GO TO 2.

Fixed ON>>GO TO 3.

Fixed OFF>>Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key system) or BCS-135, "Removal and Installation" (without Intelligent Key system).

2.CHECK INTERIOR ROOM LAMP CONTROL OPEN CIRCUIT

  1.  Turn power switch OFF.
  2.  Disconnect BCM connector, map lamp assembly and room lamp connector.
  3.  Check continuity between BCM harness connector and map lamp harness connector.

Check interior room lamp control open circuit

  1. Check continuity between BCM harness connector and room lamp harness connector.

Check interior room lamp control open circuit

Is the inspection result normal? YES >> Replace map lamp or room lamp.

NO >> Repair or replace harnesses.

3.CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT

  1.  Turn power switch OFF.
  2.  Disconnect BCM connector, map lamp connector and room lamp connector.
  3.  Check continuity between BCM harness connector and ground.

Check interior room lamp control short circuit

Is the inspection result normal? YES >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key system) or BCS- 135, "Removal and Installation" (without Intelligent Key system).

NO >> Repair or replace harnesses.

Interior room lamp power supply circuit
Description Provides the interior room lamp power supply. Also cuts the power supply when the interior room lamp battery saver is activating. Component Function Check 1.CHECK INTERIOR ROOM LAMP ...

Luggage room lamp circuit
Description Controls the luggage room lamp (ground side) to turn the luggage room lamp ON and OFF. Diagnosis Procedure CAUTION: Before performing the diagnosis, check that the following is norma ...

Other materials:

NISSAN vehicle immobilizer system
The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. Never leave these keys in the vehicle. FCC Notice: For USA: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device ...

Unit removal and installationEMBER
REAR SUSPENSION M Exploded View Rear suspension member  Suspension member stay (RH)  Suspension member stay (LH)  Bound bumper Front Removal and Installation - FWD REMOVAL  Remove wheel and tires using power tool. Refer to WT-60, "Exploded Vie ...

Rear window defogger and door mirror defogger do not operate
Diagnosis Procedure Regarding Wiring Diagram information, refer to DEF-12, "Wiring Diagram". 1. CHECK REAR WINDOW DEFOGGER SWITCH Check rear window defogger switch. Refer to DEF-22, "WITH MANUAL A/C : Component Function Check". Is the inspection result normal? YES >& ...

© 2014-2024 Copyright www.nirogue.com