Nissan Rogue Owners Manual: Heater operation
Heating
This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets and the side vent outlets.
- Press the
button to
change to fresh
air intake mode. The 
indicator
light
will turn off for normal heating. - Press the
air flow
control button. - Turn the fan control dial to the desired position
- Turn the temperature control dial to the desired position between the middle and the hot position.
Ventilation
This mode directs outside air to the side and center vents.
- Press the
button to
change to fresh
air intake mode. The 
indicator
light
will turn off. - Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position.
Defrosting or defogging
This mode directs the air to the defrost outlets to defrost/defog the windows.
- Press the defrost/defog button
. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position between the middle and the hot position.
- To quickly remove ice or fog from the windows, turn the fan control dial to the highest setting and the temperature control to the full HOT position.
- When the
position is
selected, the air
conditioner automatically turns on if the outside
temperature is more than 36°F (2°C).This dehumidifies the air which helps defog the windshield. The
indicator
automatically
turns off, allowing outside air to be
drawn into the passenger compartment to
further improve the defogging performance.The recirculation mode cannot be activated in the
position.
Bi-level heating
The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets.
- Press the
button to
change to fresh
air intake mode. The 
will turn off. - Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position.
Heating and defogging
This mode heats the interior and defogs the windshield.
- Press the
air flow
control button. - Turn the fan control dial to the desired position.
- Turn the temperature control dial to the desired position between the middle and the hot position.
- When the
position is
selected, the air
conditioner automatically turns on if the outside
temperature is more than 36°F (2°C).This dehumidifies the air which helps defog the windshield. The
indicator
automatically
turns off, allowing outside air to be
drawn into the passenger compartment to
further improve the defogging performance.
Operating tips
Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation.
Controls
Fan control dial
The fan control dial turns the fan on and off, and
controls fan speed.
Air flow control buttons
The air flow control buttons allow you to select
the air flow outlets.
MAX A/C ...
Air conditioner operation
Start the engine, turn the fan control dial to the
desired position, and press the
button to
activate the air conditioner. When the air conditioner
is on, cooling and dehumidifying functions
ar ...
Other materials:
Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT
BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
...
Parking brake front cable
Removal and Installation
REMOVAL
Remove the instrument lower panel LH. Refer to IP-22, "Removal and
Installation".
Remove driver seat (LH). Refer to SE-32, "DRIVER SIDE : Removal
and Installation"
Remove the center console. Refer to IP-18, "R ...
Rear disc brake
Brake Burnishing
CAUTION:
Burnish contact surfaces between brake pads and disc brake
rotor according to the following procedure
after refinishing the disc brake rotor, replacing brake pads or if a soft
pedal occurs at very low
mileage.
Be careful of vehicle speed. Brakes ...
