Nissan Rogue manuals

Nissan Rogue Service Manual: Fuel pump

Nissan Rogue Service Manual / Engine / Engine Control System / DTC/Circuit diagnosis / Fuel pump

Description

Sensor Input signal to ECM ECM Function Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)		 Engine speed* Fuel pump control Fuel pump relay

↓

Fuel pump
Battery Battery voltage*

*: ECM determines the start signal status by the signals of engine speed and battery voltage.

The ECM activates the fuel pump for several seconds after the ignition switch is turned ON to improve engine start ability. If the ECM receives a engine speed signal from the camshaft position sensor (PHASE), it knows that the engine is rotating, and causes the pump to operate. If the engine speed signal is not received when the ignition switch is ON, the engine stalls. The ECM stops pump operation and prevents battery discharging, thereby improving safety. The ECM does not directly drive the fuel pump. It controls the ON/OFF fuel pump relay, which in turn controls the fuel pump.

Condition Fuel pump operation
Ignition switch is turned to ON Operates for 1 second.
Engine running and cranking Operates.
When engine is stopped Stops in 1.5 seconds.
Except as shown above Stops.

Component Function Check

1.CHECK FUEL PUMP FUNCTION

  1. Turn ignition switch ON.
  2.  Pinch fuel feed hose with two fingers.

Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-467, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK FUEL PUMP RELAY CONTROL SIGNAL

  1.  Turn ignition switch ON.
  2.  Check the voltage between ECM harness connector.

Check fuel pump relay control signal

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK FUEL PUMP RELAY CONTROL SIGNAL CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect ECM harness connector.
  3.  Disconnect IPDM E/R harness connector.
  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.

Check fuel pump relay control signal circuit

Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

3.CHECK FUEL PUMP POWER SUPPLY

  1.  Turn ignition switch OFF.
  2.  Disconnect “fuel level sensor unit and fuel pump” harness connector.
  3.  Turn ignition switch ON.
  4.  Check the voltage between “fuel level sensor unit and fuel pump” harness connector and ground.

Check fuel pump power supply

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 4.

4.CHECK FUEL PUMP POWER SUPPLY CIRCUIT

  1.  Turn ignition switch OFF.
  2.  Disconnect IPDM E/R harness connector.
  3.  Check the continuity between IPDM E/R harness connector and “fuel level sensor unit and fuel pump” harness connector.

Check fuel pump power supply circuit

  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

5.CHECK FUEL PUMP GROUND CIRCUIT

  1.  Check the continuity between “fuel level sensor unit and fuel pump” and ground.

Check fuel pump power supply circuit

  1. Also heck harness for short to power.

Is the inspection result normal?

YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK FUEL PUMP

Refer to EC-469, "Component Inspection".

Is the inspection result normal? YES >> GO TO 7.

NO >> Replace “fuel level sensor unit and fuel pump”. Refer to FL-6, "Removal and Installation".

7.CHECK INTERMITTENT INCIDENT

Perform GI-41, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-35, "Removal and Installation".

NO >> Repair or replace harness or connectors.

Component Inspection

1.CHECK FUEL PUMP

  1.  Turn ignition switch OFF.
  2.  Disconnect “fuel level sensor unit and fuel pump” harness connector.
  3.  Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.

Check fuel pump

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace “fuel level sensor unit and fuel pump”. Refer to FL-6, "Removal and Installation".

Fuel injector
Component Function Check 1.INSPECTION START Turn ignition switch to START. Are any cylinders ignited? YES >> GO TO 2. NO >> Proceed to EC-464, "Diagnosis Procedure". 2. ...

Ignition signal
Component Function Check 1.INSPECTION START Turn ignition switch OFF, and restart engine. Does the engine start? YES-1 >> With CONSULT: GO TO 2. YES-2 >> Without CONSULT: GO TO 3. ...

Other materials:

Diagnosis system (BCM) (with intelligent key system)
COMMON ITEM COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT performs the following functions via CAN communication with BCM. Direct Diagnostic Mode Description Ecu Identification The BCM part number is displayed. Self Diagnostic ...

Wiring diagram
AUTOMATIC AIR CONDITIONING SYSTEM Wiring Diagram ...

Power window retained power operation does not operate properly
Diagnosis Procedure 1.CHECK DOOR SWITCH Check door switch. Refer to DLK-149, "Component Function Check" (with Intelligent Key system) or DLK-319, "Component Function Check" (without Intelligent Key system). Is the inspection result normal? YES >> GO TO 2. NO ...

© 2014-2024 Copyright www.nirogue.com