Nissan Rogue manuals

Nissan Rogue Service Manual: Front washer nozzle and tube

Nissan Rogue Service Manual / Driver controls / Wiper & Washer / Removal and installation / Front washer nozzle and tube

Exploded View

Exploded View

  1. Cowl top cover
  2. Front washer tube
  3. Front washer nozzle (LH)
  4.  Front washer nozzle (RH)

Pawl
Clip

Exploded View

Exploded View

  1. Cowl top cover
  2. Front washer tube

Clip

Removal and Installation - Front Washer Nozzle

REMOVAL

  1.  Remove front wiper arms (LH/RH). Refer to WW-63, "Removal and Installation".
  2. Release pawls using suitable tool (A) and remove cowl top side trim cover (1) (LH/RH).

    : Pawl

Removal

  1. Disconnect front washer tube connector.

Removal

  1. Release pawls and remove front washer nozzle (LH/RH).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION: Adjust the nozzle spray pattern. Refer to WW-61, "Inspection and Adjustment".

Removal and Installation - Front Washer Tube

REMOVAL

  1.  Disconnect front washer tube connector.

Removal

  1. Remove engine side cover. Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  2.  Remove engine undercover. Refer to EXT-37, "ENGINE UNDER COVER : Removal and Installation".
  3.  Partially remove fender protector. Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  4.  Unclip front washer hose and remove.

INSTALLATION

Installation is in the reverse order of removal.

Inspection and Adjustment

WASHER TUBE INSPECTION

Check that air can pass through the check valve splitter by blowing into the check valve splitter and that air cannot flow in the opposite direction.

O: Air can flow
X: Air cannot flow

Washer tube inspection

ADJUSTMENT

If operating properly, spray positions should match the positions shown. If spray positions do not match, confirm the rear washer nozzle is properly seated and working properly. If the spray positions still do not match as shown, then replace the front washer nozzle. Refer to WW-60, "Removal and Installation - Front Washer Nozzle"

Adjustment

  1. Windshield glass
  2. Black printed area line
  3. Front washer nozzle (LH/RH)
  4.  Center line
  5.  409 mm (16.10 in)
  6.  103 mm (4.06 in)
  7.  497 mm (19.57 in)
  8.  398 mm (15.67 in)
  9.  100 mm (3.94 in)
  10.  356 mm (14.02 in)
  11.  127 mm (5.00 in)
  12.  93 mm (3.66 in)
  13. 80 mm (3.15 in)
  14.  133 mm (5.24 in)
  15. 354 mm (13.94 in)
  16.  90 mm (3.54 in)
  17. 380 mm (14.96 in)
  18. 496 mm (19.53 in)
  19.  103 mm (4.06 in)
  20. 409 mm (16.10 in)
Washer fluid level switch
Removal and Installation The washer fluid level switch is serviced as a part of the washer tank. Refer to WW-56, "Removal and Installation". ...

Front wiper arm
Exploded View Front wiper blade (RH) Front wiper arm (RH)  Front wiper arm cover  Front wiper drive assembly Front wiper arm (LH)  Front wiper blade (LH) Removal ...

Other materials:

Preparation
Commercial Service Tool Tool name Description Ball joint remover Removing wheel stud Power tools Loosening nuts, screws, and bolts ...

Key switch signal circuit (without intelligent key)
Description Transmits a key switch signal to the BCM. Component Function Check 1. CHECK BCM INPUT SIGNAL Select "Data Monitor" for "BCM" and check the "KEY ON SW" monitor value. Is the inspection result normal? YES >> Inspection End. NO >> Refer ...

Wiring diagram
HEADLAMP Wiring Diagram DAYTIME LIGHT SYSTEM Wiring Diagram AUTO LIGHT SYSTEM Wiring Diagram FRONT FOG LAMP SYSTEM Wiring Diagram TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM Wiring Diagr ...

В© 2014-2024 Copyright www.nirogue.com