Nissan Rogue Service Manual: Excessive operation frequency
Description
VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function, Brake assist function, hill start assist function or Brake force distribution function operates in excessive operation frequency.
Diagnosis Procedure
1.CHECK BRAKING FORCE
Check brake force using a brake tester.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Check that there is no excessive looseness in front and rear axle.
- 2WD: Refer to FAX-7, "Inspection" (front) or RAX-6, "Inspection" (rear).
- AWD: Refer to FAX-38, "Inspection" (front) or RAX-14, "Inspection" (rear).
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK WHEEL SENSOR
Check wheel sensor.
- Check installation and damage of wheel sensor.
- Check connection of wheel sensor harness connector.
- Check terminal of wheel sensor harness connector.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair installation or replace wheel sensor.
- Front wheel sensor: Refer to BRC-132, "FRONT WHEEL SENSOR : Removal and Installation".
- Rear wheel sensor: Refer to BRC-134, "REAR WHEEL SENSOR : Removal and Installation".
4.CHECK SENSOR ROTOR
Check that there is no looseness, damage or foreign material on sensor rotor.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair installation or replace sensor rotor.
- Front sensor rotor: Refer to BRC-135, "FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor".
- Rear sensor rotor: Refer to BRC-135, "REAR SENSOR ROTOR : Removal and Installation - Rear Sensor Rotor".
5.CHECK WARNING LAMP TURNS OFF
Check that ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF approx. 1 second after key switch is turned ON and stay in OFF status during driving.
CAUTION: Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake fluid is less than the specified level (brake fluid level switch is ON). Is the inspection result normal? YES >> Normal NO >> GO TO 6.
6.PERFORM THE SELF-DIAGNOSIS
With CONSULT
- Turn the ignition switch OFF → ON.
CAUTION:
- Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
- Set the vehicle to READY/Start the engine.
- Repeat step 1 two or more times.
- Perform self-diagnosis for “ABS”.
Is any DTC detected? YES >> Check the DTC. Refer to BRC-55, "DTC Index".
NO >> Inspection End.
Unexpected brake pedal reaction
Description
A malfunction of brake pedal feel (height or others) is detected when brake
pedal is depressed.
Diagnosis Procedure
1.CHECK FRONT AND REAR AXLE
Check that there is no excessive loose ...
Other materials:
Basic inspection
DIAGNOSIS AND REPAIR WORK FLO
Work Flow
OVERALL SEQUENCE
DETAILED FLOW
1.GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the
condition and the environment when
the incident/malfunction occurs).
Check operation condition of the ...
C1730, C1731, C1732, C1733 flat tire
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTC ...
Continuously Variable Transmission (CVT) fluid
CAUTION
NISSAN recommends using Genuine
NISSAN CVT Fluid NS-3 ONLY in
NISSAN CVTs. Do not mix with other
fluids.
Do not use Automatic transmission
fluid (ATF) or Manual transmission fluid
in a NISSAN CVT, as it may damage the
CVT. Damage caused by t ...
