Nissan Rogue Service Manual: DTC/Circuit diagnosis
- Trouble diagnosis - specification value
- Power supply and ground circuit
- U0101 CAN comm circuit
- U1001 CAN comm circuit
- U1040 ENG comm circuit
- U1044 ENG comm circuit
- U1050, U1051 LIN communication
- P0011 IVT control
- P0014 EVT control
- P0031, P0032 A/F sensor 1 heater
- P0037, P0038 HO2S2 heater
- P0075 intake valve timing control
- P0078 EVT control solenoid valve
- P0101 MAF sensor
- P0102, P0103 MAF sensor
- P0111 IAT sensor
- P0112, P0113 IAT sensor
- P0116 ECT sensor
- P0117, P0118 ECT sensor
- P0122, P0123 TP sensor
- P0125 ECT sensor
- P0127 IAT sensor
- P0128 thermostat function
- P0130 A/F sensor 1
- P0131 A/F sensor 1
- P0132 A/F sensor 1
- P0137 HO2S2
- P0138 HO2S2
- P0139 HO2S2
- P014C, P014D, P015A, P015B, A/F sensor 1
- P0171 fuel injection system function
- P0172 fuel injection system function
- P0181 FTT sensor
- P0182, P0183 FTT sensor
- P0196 EOT sensor
- P0197, P0198 EOT sensor
- P0222, P0223 TP sensor
- P0300, P0301, P0302, P0303, P0304 misfire
- P0327, P0328 KS
- P0335 CKP sensor (POS)
- P0340 CMP sensor (phase)
- P0420 three way catalyst function
- P0441 EVAP control system
- P0443 EVAP canister purge volume control solenoid valve
- P0444, P0445 EVAP canister purge volume control solenoid
- P0447 EVAP canister vent control valve
- P0448 EVAP canister vent control valve
- P0451 EVAP control system pressure sensor
- P0452 EVAP control system pressure sensor
- P0453 EVAP control system pressure sensor
- P0456 EVAP control system
- P0460 fuel level sensor
- P0461 fuel level sensor
- P0462, P0463 fuel level sensor
- P0500 VSS
- P0506 ISC system
- P0507 ISC system
- P050A, P050B, P050E cold start control
- P0520 EOP sensor
- P0524 engine oil pressure
- P052A, P052B intake valve timing control
- P0603, P062F ECM
- P0604 ECM
- P0605 ECM
- P0606 ECM
- P0607 ECM
- P060A ECM
- P060B ECM
- P0643 sensor power supply
- P0850 PNP switch
- P1078 EVT control position sensor
- P1148 closed loop control
- P117A air fuel ratio
- P1212 TCS communication line
- P1217 engine over temperature
- P1225 TP sensor
- P1226 TP sensor
- P155D generator
- 1564 ASCD steering switch
- P1568 signal invalid
- P1572 brake pedal position switch
- P1574 ASCD vehicle speed sensor
- P1715 input speed sensor
- P1805 brake switch
- P2004 intake manifold runner control valve
- P2014, P2016, P2017, P2018 intake manifold runner control valve position sensor
- P2096, P2097 A/F sensor 1
- P2100, P2103 throttle control motor relay
- P2101 electric throttle control function
- P2118 throttle control motor
- P2119 electric throttle control actuator
- P2122, P2123 APP sensor
- P2127, P2128 APP sensor
- P2135 TP sensor
- P2138 APP sensor
- P2610 ECM internal timer
- Brake pedal position switch
- Cooling fan
- Electrical load signal
- Fuel injector
- Fuel pump
- Ignition signal
- Information display (ASCD)
- Malfunction indicator lamp
- On board refueling vapor recovery (ORVR)
- Refrigerant pressure sensor
- Sensor power supply2 circuit
How to erase permanent DTC
Description
OUTLINE
When a DTC is stored in ECM
When a DTC is stored in ECM and MIL is ON, a permanent DTC is erased with MIL
shutoff if the same malfunction
is not detected after performing the ...
Trouble diagnosis - specification value
Description
The specification (SP) value indicates the tolerance of the value that is
displayed in “SPEC” of “DATA MONITOR”
mode of CONSULT during normal operation of the Engine Control Sy ...
Other materials:
VDC off switch
Removal and Installation
REMOVAL
Remove the instrument lower panel LH. Refer to IP-14, "INSTRUMENT
PANEL ASSEMBLY : Removal
and Installation".
Release pawls using suitable tool and remove the VDC OFF switch
(2) from the upper switch carrier (1).
: Pawl
INST ...
C1121, C1123, C1125, C1127 ABS out valve system
DTC Logic
DTC DETECTION LOGIC
DTC
Display Item
Malfunction detected condition
Possible causes
C1121
FR LH OUT ABS SOL
When a malfunction is detected in front LH ABS OUT
valve.
Harness or connector
ABS actuator and electric unit
(control u ...
Heater operation
Heating
This mode is used to direct heated air to the foot
outlets. Some air also flows from the defrost
outlets and the side vent outlets.
Press the button to
change to fresh
air intake mode. The indicator
light
will turn off for normal heating.
Press the air flow ...
