Nissan Rogue manuals

Nissan Rogue Service Manual: DTC/circuit diagnosis

Nissan Rogue Service Manual / Electrical & power control / LAN System / CAN gateway / DTC/circuit diagnosis

B2600-46 CONFIG ERROR

DTC Description

DTC DETECTION LOGIC

DTC

Trouble diagnosis (Trouble diagnosis contents)

Detecting condition
B2600-46 CONFIG ERROR (Configuration error) When errors are detected in the configuration data stored in the BCM (CAN gateway function).

POSSIBLE CAUSE

BCM

FAIL-SAFE

Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1.  Turn ignition switch ON and wait at least 2 seconds or more.
  2.  Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
  3.  Check DTC.

Is DTC B2600-46 detected? YES >> Proceed to LAN-78, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.PERFORM DTC CONFIRMATION PROCEDURE AGAIN

  1.  Turn ignition switch ON.
  2.  Erase DTC.
  3.  Perform DTC confirmation procedure again. Refer to LAN-78, "DTC Description".
  4.  Check DTC.

Is DTC B2600-46 detected again? YES >> Replace BCM. Refer to the following.

NO >> INSPECTION END

B2600-55 CONFIG ERROR

DTC Description

DTC DETECTION LOGIC

DTC

Trouble diagnosis (Trouble diagnosis contents)

Detecting condition
B2600-55 CONFIG ERROR (Configuration error) When no data are stored in the BCM (CAN gateway function).

POSSIBLE CAUSE

FAIL-SAFE

Transmission and reception of the signal between CAN communication circuit 1 and CAN communication circuit 2 are stopped

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1.  Turn ignition switch ON and wait at least 2 seconds or more.
  2.  Select “Self Diagnostic Result” mode of “CAN GATEWAY” using CONSULT.
  3.  Check DTC.

Is DTC B2600-55 detected? YES >> Proceed to LAN-79, "Diagnosis Procedure".

NO-1 >> To check malfunction symptom before repair: GI-41, "Intermittent Incident".

NO-2 >> Confirmation after repair: INSPECTION END

Diagnosis Procedure

1.PERFORM CONFIGURATION OF CAN GATEWAY

Perform CAN gateway configuration. Refer to LAN-77, "Work Procedure".

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE AGAIN

  1.  Turn ignition switch ON.
  2.  Perform DTC confirmation procedure again. Refer to LAN-79, "DTC Description".
  3.  Check DTC.

Is DTC B2600-55 detected again? YES >> Replace BCM. Refer to the following.

NO >> INSPECTION END

Basic inspection
CONFIGURATION (CAN GATEWAY) Work Procedure 1.WRITING MODE SELECTION CONSULT Configuration Select “Re/programming, Configuration” of CAN gateway. When writing saved data>>GO TO 2. W ...

CAN system (type 1)
DTC/CIRCUIT DIAGNOSIS MAIN LINE BETWEEN IPDM-E AND DLC CIRCUIT Diagnosis Procedure 1.CHECK CONNECTOR  Turn the ignition switch OFF.  Disconnect the battery cable from the negative t ...

Other materials:

Hazard warning flasher switch
Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash. WARNING  If stopping for an emergency, be sure to move the vehicle well off the road.  Do not use the hazard warning flashers while ...

Run-flat tires (if so equipped)
Run-flat tires are those tires that can be used temporarily if they are punctured. For additional information, refer to “Run-flat tires” in “Maintenance and do-it-yourself.” For additional information, refer to the tire safety information in the Warranty Information Booklet. WAR ...

USB (Universal Serial Bus) Connection Port (models with Navigation System) (if so equipped)
USB (Universal Serial Bus) Connection Port (models with Navigation System) Connecting a device to the USB Connection Port WARNINGDo not connect, disconnect, or operate the USB device while driving. Doing so can be a distraction. If distracted you could lose control of your ...

© 2014-2025 Copyright www.nirogue.com