Nissan Rogue Owners Manual: Cruise control operations
The cruise control allows driving at a speed between 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal.
To turn on the cruise control, push the ON·OFF switch ON. The CRUISE indicator light in the vehicle information display will illuminate.
To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. Take your foot off the accelerator pedal. Your vehicle maintains the set speed.
- To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previously set speed.
- The vehicle may not maintain the set speed when going up or down steep hills. If this happens, drive without the cruise control.
To cancel the preset speed, use one of the following three methods.
- Push the CANCEL button.
- Tap the brake pedal.
- Push the ON·OFF switch off. The CRUISE indicator light in the vehicle information display goes out.
The cruise control is automatically canceled if:
- you depress the brake pedal while pushing
the ACCEL/RES or SET/COAST switch.
The preset speed is deleted from memory.
- the vehicle slows down more than 8 MPH (13 km/h) below the set speed.
- you move the shift lever to N (Neutral).
To reset at a faster cruising speed, use one of the following three methods.
- Depress the accelerator pedal. When the vehicle attains the desired speed, push and release the COAST/SET switch.
- Push and hold the ACCEL/RES switch.
When the vehicle attains the speed you desire, release the switch.
- Push and release the ACCEL/RES switch.
Each time you do this, the set speed increases by about 1 MPH (1.6 km/h).
To reset at a slower cruising speed, use one of the following three methods.
- Lightly tap the brake pedal. When the vehicle attains the desired speed, push the COAST/SET switch and release it.
- Push and hold the COAST/SET switch. Release the switch when the vehicle slows to the desired speed.
- Push and release the COAST/SET switch.
Each time you do this, the set speed decreases by about 1 MPH (1.6 km/h).
To resume the preset speed, push and release the ACCEL/RES switch. The vehicle returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).
To turn off the cruise control, use one of the following three methods.
- Push the CANCEL button.
- Tap the brake pedal.
- Push the ON·OFF switch off. The CRUISE indicator light in the vehicle information display goes out.
Precautions on cruise control
Precautions on cruise control
CANCEL switch
ACCEL/RES switch
COAST/SET switch
ON/OFF switch
If the cruise control system malfunctions, it
cancels automaticall ...
Forward Collision Warning (FCW) system
(if so equipped)
The Forward Collision Warning (FCW) system
will warn the driver by flashing the FCW indicator
light and providing a warning chime when your
vehicle is getting close to the vehicle ahead in the
tra ...
Other materials:
System description
COMPONENT PARTS
POWER DOOR LOCK SYSTEM
POWER DOOR LOCK SYSTEM : Component Parts Location
No
Component
Function
1
BCM
Controls the door lock system.
Refer to BCS-7, "BODY CONTROL SYSTEM : Component Parts Location" for
detailed
install ...
Rear regulator
Exploded View
Rear door panel
Rear door glass corner finisher
Rear door glass rear run channel
Rear door regulator assembly
Rear door glass power window motor
Rear door glass
Rear door glass rubber run channel
Removal and Installation
REMOVAL
Remove the re ...
C1769 configuration setting
DTC Description
This procedure must be performed:
After replacement of BCM.
DTC DETECTION LOGIC
DTC
Display Item
Malfunction detected condition
C1769
CONFIG SETTING
(Configuration setting)
Tire air pressure monitoring system configuration cannot be
p ...
