Nissan Rogue manuals

Nissan Rogue Service Manual: Camshaft valve clearance

Camshaft valve clearance

  1.  Remove the fender protector side cover (RH). Refer to EXT-28, "FENDER PROTECTOR : Exploded View".
  2.  Remove the rocker cover. Refer to EM-37, "Exploded View".
  3.  Turn crankshaft pulley clockwise when viewed from front to align TDC identification mark (B) with timing indicator (A).

NOTE: Do not confuse TDC mark (B) with paint marks (C).

Camshaft valve clearance

  1. At this time, check that the both intake and exhaust cam lobes of No. 1 cylinder face outside.

Camshaft valve clearance

  1. Measure valve clearances with a suitable tool at locations marked (X) in the table below.

Camshaft valve clearance

Engine front

Valve clearance: Refer to EM-116, "Camshaft".

Camshaft valve clearance

  1. Turn crankshaft one complete revolution (360°) and align mark on crankshaft pulley with pointer.
  2.  Measure valve clearances with a suitable tool at locations marked (X) in the table below.

Camshaft valve clearance

If out of specifications, make necessary adjustment.

Engine front

ADJUSTMENT

NOTE:

  1.  Remove camshaft. Refer to EM-64, "Exploded View".
  2.  Remove the valve lifters at the locations that are outside the standard.
  3.  Measure the center thickness of the removed valve lifters with a suitable tool (A).

Adjustment

  1. Use the equation below to calculate valve lifter thickness for replacement.

t = t1 + (C1 - C2)
t = Thickness of replacement valve lifter.
t1 = Thickness of removed valve lifter.
C1 = Measured valve clearance.
C2 = Standard valve clearance.

  1.  Install the selected valve lifter.
  2.  Install camshaft. Refer to EM-64, "Exploded View".
  3.  Install timing chain and related parts. Refer to EM-44, "Exploded View".
  4.  Manually rotate crankshaft pulley a few rotations.
  5.  Check that valve clearances for cold engine are within specifications by referring to the specified values.

Valve clearance Refer to EM-116, "Camshaft".

  1. Install all removed parts in the reverse order of removal.
  2.  Warm up the engine, and check for unusual noise and vibration.

Adjustment

Spark plug
Exploded view Ignition coil  Spark plug Rocker cover Removal and installation REMOVAL  Remove air duct assembly.  Remove ignition coil. Refer to EM-36, "Ex ...

Compression pressure
CHECKING COMPRESSION PRESSURE  Warm up the engine to full operating temperature.  Release the fuel pressure. Refer to EC-144, "Work Procedure".  Remove the ignition co ...

Other materials:

Information display (ASCD)
Component Function Check 1.CHECK INFORMATION DISPLAY  Start engine.  Press ASCD MAIN switch on ASCD steering switch.  Drive the vehicle at more than 40 km/h (25 MPH). CAUTION: Always drive vehicle at a safe speed.  Press SET/− switch.  Check that the r ...

Windshield glass
Exploded View Mirror base Spacer Windshield glass Windshield glass lower molding Windshield glass molding Roof Cowl top cover ody side outer ront pillar finisher Headlining  7.0 mm (0.28 in) 12 mm (0.47 in)  Adhesive Removal and Installation REMO ...

Basic inspection
DIAGNOSIS AND REPAIR WORK FLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION FOR SYMPTOM  Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).  Check operation condition of the ...

© 2014-2022 Copyright www.nirogue.com