Nissan Rogue manuals

Nissan Rogue Service Manual: C1708, C1709, C1710, C1711 transmitter (no data)

Nissan Rogue Service Manual / Suspension / Road Wheels & Tires / DTC/circuit diagnosis / C1708, C1709, C1710, C1711 transmitter (no data)

DTC Logic

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

DTC DETECTION LOGIC

DTC Display Item Malfunction Detected Condition Possible Cause
C1708 [NO - DATA] - FL Data signal from the front LH wheel sensor cannot be detected.
  • Driving in area with radio interference.
  •  ID registration incomplete
  •  Tire pressure sensor
  •  Harness or connectors
  •  BCM
C1709 [NO - DATA] - FR Data signal from the front RH wheel sensor cannot be detected.
C1710 [NO - DATA] - RR Data signal from the rear RH wheel sensor cannot be detected.
C1711 [NO - DATA] - RL Data signal from the rear LH wheel sensor cannot be detected.

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT

  1.  Perform tire pressure sensor ID registration. Refer to WT-21, "Work Procedure".
  2.  Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.

    NOTE: Avoid driving in areas with radio interference.

  3.  Perform Self Diagnostic Result.

Is DTC C1708, C1709, C1710, or C1711 detected? YES >> Proceed to WT-26, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

Regarding Wiring Diagram information, refer to WT-15, "Wiring Diagram".

1.CHECK TIRE PRESSURE SIGNAL

With CONSULT

  1.  Select “AIR PRESSURE MONITOR” from “BCM” Data Monitor.
  2.  Check that the air pressures match the specified value.

Monitor item

Displayed value
AIR PRESS FL Approximately equal to specified value. Refer to WT-65, "Tire Air Pressure".
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL

Are all tire pressures displayed 0 kPa (psi)? YES >> GO TO 2.

NO >> Replace applicable tire pressure sensor. Refer to WT-61, "Removal and Installation".

2.CHECK BCM POWER CIRCUIT

Check voltage between BCM connector M20 terminal 161 and ground.

BCM

Ground

Voltage (Approx.)

Connector Terminal
M20 161 Battery voltage

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3.CHECK BCM GROUND CIRCUIT

Check continuity between BCM connector M20 and ground.

BCM Ground Continuity
Connector Terminal
M20 170 Yes
171

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness or connectors.

4.TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to WT-21, "Work Procedure".

Can the tire pressure sensor ID registration be completed? YES >> GO TO 5.

NO >> Replace applicable tire pressure sensor. Refer to WT-61, "Removal and Installation".

5.RECHECK TIRE PRESSURE SIGNAL

With CONSULT

  1.  Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
  2.  Select “AIR PRESSURE MONITOR” from “BCM” Data Monitor.
  3.  Check that the air pressures match the specified value.

Monitor item

Displayed value

AIR PRESS FL Approximately equal to specified value. Refer to WT-65, "Tire Air Pressure".
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL

Does Data Monitor display specified value without turning tire pressure warning lamp ON? YES >> Inspection End.

NO >> Replace BCM. Refer to BCS-75, "Removal and Installation" (with Intelligent Key System) or BCS- 135, "Removal and Installation" (without Intelligent Key System).

C1704, C1705, C1706, C1707 low tire pressure
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.  Activate and dis ...

C1716, C1717, C1718, C1719 transmitter (pressure data)
DTC Logic NOTE: The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.  Activate and dis ...

Other materials:

Bluetooth® Hands-Free Phone System with Navigation System (if so equipped)
WARNING  Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.  If you are unable to devote full attention to vehicl ...

Parking lights, low beams and roadside parking lights
General information If the driver's door is opened when the drive-ready state is switched off, the exterior lighting is automatically switched off after a period of time. Parking lights General information The parking lights can only be switched on in the low speed range. Switching on Press the butt ...

Front wiper motor
Removal and Installation REMOVAL  Remove the front drive assembly. Refer to WW-66, "Removal and Installation".  Remove the bolts (A) from the front wiper drive assembly (1) and the front wiper motor (2). Separate the wiper motor (1) from the front wiper drive ...

© 2014-2022 Copyright www.nirogue.com