Nissan Rogue manuals

Nissan Rogue Service Manual: C119A vacuum sensor

DTC Logic

DTC DETECTION LOGIC

DTC Display Item Malfunction detected condition Possible causes
C119A VACUUM SEN VOLT When a malfunction is detected in supply power voltage of vacuum sensor.
  • Harness or connector
  •  Vacuum sensor (brake booster)
  •  ABS actuator and electric unit (control unit)

DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

With CONSULT.

  1.  Turn the ignition switch ON.
  2.  Perform self-diagnostic result.

Is DTC C119A detected? YES >> Proceed to diagnosis procedure. Refer to BRC-111, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".

1.CHECK VACUUM SENSOR POWER SUPPLY

  1.  Turn the ignition switch OFF.
  2. Disconnect vacuum sensor harness connector.
  3.  Check voltage between vacuum sensor harness connector and ground.

Check vacuum sensor power supply

  1. Turn the ignition switch ON.

    CAUTION: Never start engine.

  2.  Check voltage between vacuum sensor harness connector and ground.

Check vacuum sensor power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK VACUUM SENSOR POWER SUPPLY CIRCUIT

  1.  Turn the ignition switch OFF.
  2.  Disconnect ABS actuator and electric unit (control unit) harness connector.
  3.  Check continuity between vacuum sensor harness connector and ABS actuator and electric unit (control unit) harness connector.

Check vacuum sensor power supply circuit

  1. Check continuity between vacuum sensor harness connector and ground.

Check vacuum sensor power supply circuit

Is the inspection result normal? YES >> Perform diagnosis of ABS actuator and electric unit (control unit) power supply and ground circuit.

Refer to BRC-111, "Diagnosis Procedure".

NO >> Repair or replace malfunctioning components.

3.CHECK VACUUM SENSOR GROUND CIRCUIT

  1.  Turn the ignition switch OFF.
  2.  Check continuity between vacuum sensor harness connector and ground.

Check vacuum sensor ground circuit

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning components.

4.CHECK TERMINAL

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Repair or replace malfunctioning components.

C1199 brake booster
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1199 BRAKE BOOSTER When brake booster vacuum is approx. 0 kPa (0 mm- ...

U1000 CAN COMM CIRCUIT
Description CAN communication allows a high rate of information transmission through the two communication lines (CAN-H line and CAN-L line) connecting various control units in the system. Each ...

Other materials:

Removal and installation
BCM (BODY CONTROL MODULE) Removal and Installation For removal and installation of the BCM (Body Control Module), refer to BCS-75, "Removal and Installation". PUSH-BUTTON IGNITION SWITCH Removal and Installation REMOVAL  Remove NATS antenna amp. Refer to SEC-110, "Remo ...

Front power window switch (passenger side)
Description Front power window motor RH will be operated if front power window switch RH is operated. Component Function Check 1. CHECK FRONT POWER WINDOW SWITCH RH FUNCTION Check front power window motor RH operation with front power window switch RH. Is the inspection result normal? YES ...

Camshaft
Exploded View Camshaft position sensor (INT) O-ring Camshaft brackets (INT)  Camshaft brackets (EXH) Camshaft (INT) O-ring  Camshaft bracket (No. 1) Camshaft sprocket (INT) Front cover (partial view)  Valve timing control cover O-rings (INT)  V ...

В© 2014-2022 Copyright www.nirogue.com