Nissan Rogue manuals

Nissan Rogue Service Manual: C1199 brake booster

DTC Logic

DTC DETECTION LOGIC

DTC Display Item Malfunction detected condition Possible causes
C1199 BRAKE BOOSTER When brake booster vacuum is approx. 0 kPa (0 mm- Hg) during engine running.
  • Harness or connector
  •  Vacuum sensor (brake booster)
  •  Vacuum piping
  •  ABS actuator and electric unit (control unit)

DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

With CONSULT.

  1.  Turn the ignition switch ON.
  2.  Perform self-diagnostic result.

Is DTC C1199 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-109, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".

1.CHECK BRAKE BOOSTER

  1.  Turn the ignition switch OFF.
  2.  Check brake booster. Refer to BR-10, "Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace brake booster. Refer to BR-30, "Removal and installation".

2.CHECK VACUUM PIPING

Check vacuum piping. Refer to BR-32, "Exploded View".

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace vacuum piping. Refer to BR-32, "Removal and Installation".

3.CHECK VACUUM SENSOR CIRCUIT

  1.  Disconnect vacuum sensor harness connector.
  2.  Disconnect ABS actuator and electric unit (control unit) harness connector.
  3.  Check continuity between vacuum sensor harness connector and ABS actuator and electric unit (control unit) harness connector.

Check vacuum sensor circuit

  1. Check continuity between vacuum sensor harness connector and ground.

Check vacuum sensor circuit

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning components.

4.CHECK TERMINAL

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace malfunctioning components.

5.REPLACE VACUUM SENSOR

With CONSULT

  1.  Connect ABS actuator and electric unit (control unit) harness connector.
  2.  Replace vacuum sensor. Refer to BR-30, "Exploded View".

    CAUTION: Always replace brake booster because vacuum sensor cannot be disassembled.

  3.  Erase self-diagnosis result for “ABS”.
  4.  Turn the ignition switch OFF.
  5.  Start engine.
  6.  Perform self-diagnosis for “ABS”.

Is DTC “C1199” detected? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Inspection End.

C1198 vacuum sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1198 VACUUM SEN CIR When an open circuit is detected in vacuum ...

C119A vacuum sensor
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C119A VACUUM SEN VOLT When a malfunction is detected in supply power volt ...

Other materials:

Symptom diagnosis
PUSH-BUTTON IGNITION SWITCH DOES NOT OPERATE Description Check that vehicle Operating Conditions are as listed in “Conditions of Vehicle” below before starting Diagnosis Procedure. Make sure to check each symptom in Diagnosis Procedure. NOTE: The engine start function, door lock functio ...

P0078 EVT control solenoid valve
DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condit P0078 EX V/T ACT/CIRC-B1 (Exhaust valve control solenoid circuit bank 1) An improper voltage is sent to the ECM through exhaust valve timing co ...

Steering switch
Description When one of the steering switches is pushed, the resistance in the steering switch changes the signal to identify which button is controlling the information display. Diagnosis Procedure Regarding Wiring Diagram information, refer to MWI-32, "Wiring Diagram". 1.CHECK STE ...

© 2014-2022 Copyright www.nirogue.com