Nissan Rogue manuals

Nissan Rogue Service Manual: C1121, C1123, C1125, C1127 ABS out valve system

Nissan Rogue Service Manual / Brakes / Brake Control System / DTC/circuit diagnosis / C1121, C1123, C1125, C1127 ABS out valve system

DTC Logic

DTC DETECTION LOGIC

DTC Display Item Malfunction detected condition Possible causes
C1121 FR LH OUT ABS SOL When a malfunction is detected in front LH ABS OUT valve.
  • Harness or connector
  •  ABS actuator and electric unit (control unit)
  •  Fusible link
  •  Battery power supply system
C1123 FR RH OUT ABS SOL When a malfunction is detected in front RH ABS OUT valve.
C1125 RR LH OUT ABS SOL When a malfunction is detected in rear LH ABS OUT valve.
C1127 RR RH OUT ABS SOL When a malfunction is detected in rear RH ABS OUT valve.

DTC CONFIRMATION PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULT

With CONSULT.

  1.  Turn ignition switch OFF to ON.
  2.  Perform self-diagnostic result.

Is DTC C1121, C1123, C1125 or C1127 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-89, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-57, "Wiring Diagram".

1.CONNECTOR INSPECTION

  1. Turn ignition switch OFF.
  2.  Disconnect ABS actuator and electric unit (control unit) connectors.
  3.  Check connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace as necessary.

2.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) BATTERY POWER SUPPLY

Check voltage between ABS actuator and electric unit (control unit) connector E125 terminal 25 and ground.

Check ABS actuator and electric unit (control unit) battery power supply

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning components.

3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) GROUND CIRCUIT

Check continuity between ABS actuator and electric unit (control unit) connector E125 terminals 13, 38 and ground.

Check ABS actuator and electric unit (control unit) ground circuit

Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-136, "Removal and Installation".

NO >> Repair or replace malfunctioning components.

C1120, C1122, C1124, C1126 ABS in valve system
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1120 FR LH IN ABS SOL When a malfunction is detected in front LH ABS IN ...

C1130 engine signal
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1130 ENGINE SIGNAL 1 When a malfunction is detected in ECM system. ...

Other materials:

System
METER SYSTEM METER SYSTEM : System Description SYSTEM DIAGRAM Combination Meter Input Signal (CAN Communication Signal) DESCRIPTION Combination Meter  The combination meter controls the following items according to the signals received from each unit via CAN communicat ...

Removal and installation
HOOD Exploded View Hood hinge (RH)  Hood  Hood side seal  Hood front seal Hood center seal  Bumper rubber  Hood insulator Hood rod clamp Hood support rod  Hood rod grommet  Hood hinge (LH) HOOD ASSEMBLY HOOD ASSEMBLY : Remova ...

Preparation
Special Service Tools The actual shapes of TechMate tools may differ from those of special service tools illustrated here. Tool number (TechMate No.) Tool name Description KV38100200 (J-26233) Drift a: 65 mm (2.56 in) dia. b: 49 mm (1.93 in) dia. ...

В© 2014-2022 Copyright www.nirogue.com