Nissan Rogue manuals

Nissan Rogue Service Manual: Basic inspection

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

OVERALL SEQUENCE

Overall sequence

DETAILED FLOW

1.GET INFORMATION FOR SYMPTOM

  1.  Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).
  2.  Check operation condition of the function that is malfunctioning.

>> GO TO 2.

2.CHECK DTC

  1.  Check DTC.
  2.  Perform the following procedure if DTC is detected.
  1.  Check related service bulletins for information.

Are any symptoms described and any DTC detected? Symptom is described, DTC is detected.>>GO TO 3.

Symptom is described, DTC is not detected.>>GO TO 4.

Symptom is not described, DTC is detected.>>GO TO 5.

3.CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

Also study the normal operation and fail-safe related to the symptom.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.

4.CONFIRM THE SYMPTOM

Try to confirm the symptom described by the customer.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.

5.PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC CONFIRMATION PROCEDURE for the detected DTC and then check that DTC is detected again. At this time, always connect CONSULT to the vehicle and check self diagnostic results in real time.

If two or more DTCs are detected, refer to BCS-47, "DTC Inspection Priority Chart" (BCM) and determine trouble diagnosis order.

NOTE:

Is DTC detected? YES >> GO TO 7.

NO >> Check according to GI-41, "Intermittent Incident".

6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.

Is the symptom described? YES >> GO TO 7.

NO >> Monitor input data from related sensors or check voltage of related module terminals using CONSULT.

7.DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE

Inspect according to Diagnosis Procedure of the system.

Is malfunctioning part detected? YES >> GO TO 8.

NO >> Check according to GI-41, "Intermittent Incident".

8.REPAIR OR REPLACE THE MALFUNCTIONING PART

  1.  Repair or replace the malfunctioning part.
  2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
  3. Check DTC. If DTC is detected, erase it.

>> GO TO 9.

9.FINAL CHECK

When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is repaired securely.

When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.

Is DTC detected and does symptom remain? YES-1 >> DTC is detected: GO TO 7.

YES-2 >> Symptom remains: GO TO 4.

NO >> Before returning the vehicle to the customer, always erase DTC.

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

Description

When the battery is disconnected from the negative terminal, it is necessary to perform initial setting to operate automatic back door control system normally.

NOTE: The following specified operations are not performed under the non-initialized condition.

Work Procedure

1.INITIALIZATION

  1.  Fully close the back door manually. (When back door is already fully closed, this operation is not necessary).
  2. Perform automatic back door open/close operation of back door.
  3. Check for noise or malfunctioning during operation.
  4. Check that hazard lamp blinks and that warning buzzer operates.

NOTE: Never touch back door or allow foreign materials to be pinched in door when performing automatic back door open/close operation of back door until it is in the fully closed or fully open position. >> Inspection End.

ADDITIONAL SERVICE WHEN REPLACING BCM

Description

Perform the system initialization when replacing BCM, replacing Intelligent Key or registering an additional Intelligent Key.

Work Procedure

Refer to the CONSULT Immobilizer mode and follow the on-screen instructions.

ADDITIONAL SERVICE WHEN REPLACING AUTOMATIC BACK DOOR CONTROL UNIT

Description

When replacing control module or removing connector terminal, it is necessary to perform initial setting to operate automatic back door system normally.

NOTE: The following specified operations are not performed under the non-initialized condition.

Work Procedure

1.INITIALIZATION

  1.  Fully close the back door manually. (When back door is already fully closed, this operation is not necessary.)
  2.  Perform automatic back door open/close operation of back door.
  3.  Check for noise or malfunctioning during operation.
  4.  Check that hazard lamp blinks and that warning buzzer operates.

NOTE: Never touch back door or allow foreign materials to be pinched in door when performing automatic back door open/close operation of back door until it is in the fully closed or fully open position. >> Inspection End.

CALIBRATION OF AUTOMATIC BACK DOOR POSITION INFORMATION

Description

When the following work is performed, it is necessary to perform initial setting of automatic back door position information to operate automatic back door system.

Work Procedure

1.STEP 1

Fully close the back door manually.

>> GO TO 2.

2.STEP 2

  1.  Select “AUTO BACK DOOR” using CONSULT.
  2.  Select “RESET AUTO BACK DOOR STATUS” of “WORK SUPPORT” mode.
  3.  Touch “START” to erase automatic back door position information.

>> GO TO 3.

3.STEP 3

Operate back door opener switch and perform automatic open operation.

NOTE: At this time, automatic operation of back door is performed at half speed.

>> GO TO 4.

4.STEP 4

  1.  The back door fully opens.
  2.  Check that hazard warning lamp blinks and automatic back door warning buzzer sounds normally.

Does hazard warning lamp blink and automatic back door warning buzzer sound normally? YES >> GO TO 5.

NO >> GO TO 1.

5.STEP 5

Fully close the back door.

>> Inspection End.

Wiring diagram
POWER DOOR LOCK SYSTEM Wiring Diagram INTELLIGENT KEY SYSTEM Wiring Diagram AUTOMATIC BACK D ...

DTC/circuit diagnosis
U1000 CAN COMM CIRCUIT Description Refer to LAN-8, "System Description". DTC Logic DTC DETECTION LOGIC NOTE: U1000 can be set if a module harness was disconnected and reconnected, perh ...

Other materials:

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the ...

B0093 front door satellite sensor LH
DTC Logic DTC DETECTION LOGIC With CONSULT CONSULT name DTC DTC detecting condition Repair order DOOR SATELLITE SENSOR LH [SENSOR FAIL] B0093 Front door satellite sensor LH has malfunctioned. Refer to SRC-70, "Diagnosis Procedure". ...

The braking distance is long
Description Brake stopping distance is long when ABS function is operated. Diagnosis Procedure CAUTION: Brake stopping distance on slippery road like rough road, gravel road or snowy road may become longer when ABS is operated than when ABS is not operated 1.CHECK BRAKING FORCE Check brake ...

© 2014-2024 Copyright www.nirogue.com