Nissan Rogue Service Manual: B1430 seat belt pre-tensioner

Nissan Rogue Service Manual / Restraints / SRS Airbag Control System / DTC/circuit diagnosis / B1430 seat belt pre-tensioner

DTC Logic

DTC DETECTION LOGIC

CONSULT name	DTC	DTC detecting condition	Repair order
FRONT PRE-TEN LH CIRCUIT [OPEN]	B1430	Front LH seat belt pre-tensioner circuit is open.	Refer to SRC-59, "Diagnosis Procedure".
FRONT PRE-TEN LH CIRCUIT [VB-SHORT]		Front LH seat belt pre-tensioner circuit is shorted to a power supply circuit.
FRONT PRE-TEN LH CIRCUIT [GND-SHORT]		Front LH seat belt pre-tensioner circuit is shorted to ground.
FRONT PRE-TEN LH CIRCUIT [SHORT]		Front LH seat belt pre-tensioner circuits are shorted to each other.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-59, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-59, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-59, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Check the harness connector for the following:

Visible damage to connector or terminal
Loose terminal
Poor connection

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

Visible damage: Replace the harness.
Loose terminal: Secure the terminal.
Poor connection: Secure the connection.

2.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4 NO >> Replace the harness.

4.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.AIR BAG DIAGNOSIS SENSOR UNIT

Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.FRONT LH SEAT BELT PRE-TENSIONER

Replace the front LH seat belt pre-tensioner. Refer to SR-28, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B0029 side curtain air bag module RH

DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order CURTAIN AIRBAG MODULE RH CIRCUIT [OPEN] B0029 RH side curtain ai ...

B1431 seat belt pre-tensioner

DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order FRONT PRE-TEN RH CIRCUIT [OPEN] B1431 RH seat belt pre-tensioner ...

Other materials:

Sunshade motor assembly
Removal and Installation REMOVAL Remove the headlining. Refer to. INT-30, "Removal and Installation". Disconnect the harness connector (A) from the sunshade motor assembly (1). Remove sunshade motor assembly screws (B). Remove the sunshade motor assembl ...

Normal operating condition
Description FUEL CUT CONTROL (AT NO LOAD AND HIGH ENGINE SPEED) If the engine speed is above 1,800 rpm under no load (for example, the selector lever position is neutral and engine speed is over 1,800 rpm) fuel will be cut off after some time. The exact time when the fuel is cut off varies b ...

Removal and installation
BCM (BODY CONTROL MODULE) Removal and Installation CAUTION: Before replacing the BCM, perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to BCS-120, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Work Procedure". REMOVAL Disc ...