Description
DTC B0092 REAR SATELLITE SENSOR LH
The rear side air bag satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the rear side air bag satellite sensor LH for internal failures and its circuits for communication errors.
PART LOCATION
Refer to SRC-6, "Component Parts Location".
DTC Logic
DTC DETECTION LOGIC
With CONSULT
CONSULT name |
DTC |
DTC detecting condition |
Repair order |
C-PILLAR SATELLITE SENSOR LH [SENSOR FAIL] | B0092 | Rear side satellite sensor LH has malfunctioned. | Refer to SRC-81, "Diagnosis Procedure". |
C-PILLAR SATELLITE SENSOR LH [COMM FAIL] | Rear side satellite sensor LH communication error. | ||
C-PILLAR SATELLITE SENSOR LH [DISCONNECT] | Rear side satellite sensor LH is disconnected. | ||
C-PILLAR SATELLITE SENSOR LH [UNMATCH] | Rear side satellite sensor LH is out of specification. | ||
C-PILLAR SATELLITE SENSOR LH [GND-SHORT] | Rear side satellite sensor LH circuit is shorted to ground. |
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.CHECK SELF-DIAG RESULT
Is the DTC detected? YES (Current DTC)>>Refer to SRC-81, "Diagnosis Procedure".
YES (Past DTC)>>GO TO 2.
NO >> Inspection End.
2.ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased? YES >> Inspection End.
NO >> Refer to SRC-81, "Diagnosis Procedure".
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.CHECK SELF-DIAG RESULT
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-81, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 2.
NO >> Perform one of the following repairs:
2.CONFIRM DTC
Is DTC still current? YES >> GO TO 3 NO >> Refer to GI-41, "Intermittent Incident".
3.WIRING HARNESS
Check the wiring harness for visible damage.
NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the harness.
4.CONFIRM DTC
Is DTC still current? YES >> GO TO 5.
NO >> Refer to GI-41, "Intermittent Incident".
5.REAR SIDE SATELLITE SENSOR LH
Is DTC still current? YES >> GO TO 6.
NO >> Clear DTC. Inspection End.
6.AIR BAG DIAGNOSIS SENSOR UNIT
Is DTC still current? YES >> GO TO 7.
NO >> Clear DTC. Inspection End.
7.RELATED HARNESS
Replace the related harness.
>> END
AM radio reception
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can be bounced off the
ionosphere and bent back to earth. Because of
these characteristics, AM signals are also subject
to interference as they travel from transmitter
to r ...
Side air spoiler
Exploded View
Side air spoiler
Clip
Removal and Installation
REMOVAL
Remove side air spoiler bolts (A).
1: Side air spoiler
B: Clips
Release clips using suitable tool (A) and remove side air spoiler
(1).
: Clips
INSTALLATION
Installation is in the rev ...
Engine stand setting
NOTE:
Explained here is how to disassemble with engine stand supporting transaxle
surface. When using a different
type of engine stand, note difference in steps, etc.
Remove engine and transaxle assembly from vehicle, and separate
transaxle from engine. Refer to EM-
81, "Expl ...