Description
DTC B0091 FRONT SATELLITE SENSOR LH
The front side air bag satellite sensor LH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor the front side air bag satellite sensor LH for internal failures and its circuits for communication errors.
PART LOCATION
Refer to SRC-6, "Component Parts Location".
DTC Logic
DTC DETECTION LOGIC
With CONSULT
CONSULT name |
DTC |
DTC detecting condition |
Repair order |
B-PILLAR SATELLITE SENSOR LH [SENSOR FAIL] | B0091 | Front side air bag satellite sensor LH has malfunctioned. | Refer to SRC-75, "Diagnosis Procedure". |
B-PILLAR SATELLITE SENSOR LH [COMM FAIL] | Front side air bag satellite sensor LH communication error. | ||
B-PILLAR SATELLITE SENSOR LH [DISCONNECT] | Front side air bag satellite sensor LH is disconnected. | ||
B-PILLAR SATELLITE SENSOR LH [UNMATCH] | Front side air bag satellite sensor LH is out of specification. | ||
B-PILLAR SATELLITE SENSOR LH [GND-SHORT] | Front side air bag satellite sensor LH circuit is shorted to ground. |
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.CHECK SELF-DIAG RESULT
Is the DTC detected? YES (Current DTC)>>Refer to SRC-75, "Diagnosis Procedure".
YES (Past DTC)>>GO TO 2.
NO >> Inspection End.
2.ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased? YES >> Inspection End.
NO >> Refer to SRC-75, "Diagnosis Procedure".
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.CHECK SELF-DIAG RESULT
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-75, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 2.
NO >> Perform one of the following repairs:
2.CONFIRM DTC
Is DTC still current? YES >> GO TO 3.
NO >> Refer to GI-41, "Intermittent Incident".
3.WIRING HARNESS
Check the wiring harness for visible damage.
NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the harness.
4.CONFIRM DTC
Is DTC still current? YES >> GO TO 5.
NO >> Refer to GI-41, "Intermittent Incident".
5.FRONT SIDE AIR BAG SATELLITE SENSOR LH
Is DTC still current? YES >> GO TO 6.
NO >> Clear DTC. Inspection End.
6.AIR BAG DIAGNOSIS SENSOR UNIT
Is DTC still current? YES >> GO TO 7.
NO >> Clear DTC. Inspection End.
7.RELATED HARNESS
Replace the related harness.
>> END
C1734 BCM
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTC ...
Liquid Gasket
REMOVAL OF LIQUID GASKET SEALING
After removing the bolts and nuts, separate the mating surface and
remove the liquid gasket using Tool (A).
Tool Number : KV10111100 (J-37228)
CAUTION:
Be careful not to damage the mating surfaces.
In areas where the cutter is difficult to use, u ...
Wiring diagram
REAR WINDOW DEFOGGER SYSTEM
Wiring Diagram
...