Nissan Rogue Service Manual: B0029 side curtain air bag module RH

Nissan Rogue Service Manual / Restraints / SRS Airbag Control System / DTC/circuit diagnosis / B0029 side curtain air bag module RH

DTC Logic

DTC DETECTION LOGIC

CONSULT name	DTC	DTC detecting condition	Repair order
CURTAIN AIRBAG MODULE RH CIRCUIT [OPEN]	B0029	RH side curtain air bag module circuit is open.	Refer to SRC-57, "Diagnosis Procedure".
CURTAIN AIRBAG MODULE RH CIRCUIT [VB-SHORT]		RH side curtain air bag module circuit is shorted to a power supply circuit.
CURTAIN AIRBAG MODULE RH CIRCUIT [GND-SHORT]		RH side curtain air bag module circuit is shorted to ground.
CURTAIN AIRBAG MODULE RH CIRCUIT [SHORT]		RH side curtain air bag module circuits are shorted to each other.

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check for DTC using CONSULT.

Is the DTC detected? YES (Current DTC)>>Refer to SRC-57, "Diagnosis Procedure".

YES (Past DTC)>>GO TO 2.

NO >> Inspection End.

2.ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.

Can the DTC be erased? YES >> Inspection End.

NO >> Refer to SRC-57, "Diagnosis Procedure".

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.CHECK SELF-DIAG RESULT

Turn ignition switch ON.
Check the air bag warning lamp status. Refer to SRC-16, "On Board Diagnosis Function".

NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-57, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

Visible damage to connector or terminal
Loose terminal
Poor connection

NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including in-line connectors).

Is the inspection result normal? YES >> GO TO 2.

NO >> Perform one of the following repairs:

Visible damage: Replace the harness.
Loose terminal: Secure the terminal.
Poor connection: Secure the connection.

2.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 3.

NO >> Refer to GI-41, "Intermittent Incident".

3.WIRING HARNESS

Check the wiring harness for visible damage.

NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors).

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace the harness.

4.CONFIRM DTC

Reconnect all harness connectors.
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 5.

NO >> Refer to GI-41, "Intermittent Incident".

5.AIR BAG DIAGNOSIS SENSOR UNIT

Replace the air bag diagnosis sensor unit. Refer to SR-26, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 6.

NO >> Clear DTC. Inspection End.

6.SIDE CURTAIN AIR BAG MODULE RH

Replace the side curtain air bag module RH. Refer to SR-19, "Removal and Installation".
Turn ignition switch ON.
Check for DTC using CONSULT.

Is DTC still current? YES >> GO TO 7.

NO >> Clear DTC. Inspection End.

7.RELATED HARNESS

Replace the related harness.

>> END

B0021 side curtain air bag module IH

DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order CURTAIN AIRBAG MODULE LH CIRCUIT [OPEN] B0021 LH side curtain ai ...

B1430 seat belt pre-tensioner

DTC Logic DTC DETECTION LOGIC CONSULT name DTC DTC detecting condition Repair order FRONT PRE-TEN LH CIRCUIT [OPEN] B1430 Front LH seat belt pre-ten ...

Other materials:

Fuel level sensor unit, fuel filter and fuel pump assembly
Exploded View 1. Lock ring 2. O-ring 3. Fuel filter and fuel pump assembly 4. Fuel level sensor and fuel tank temperature sensor 5. Lock ring 6. O-ring 7. Sub fuel level sensor assembly 8. Fuel tank Fron CAUTION: Do not remove or disassemble parts unless instructed as shown. R ...

Component parts
CVT CONTROL SYSTEM CVT CONTROL SYSTEM : Component Parts Location Engine room, LH Transaxle assembly No. Component Function 1 Combination meter Mainly transmits the following signal to TCM via CAN communication. Overdrive control switch signal ...

Removal and installation
NATS ANTENNA AMP. Removal and Installation REMOVAL Remove the steering column covers. Refer to IP-17, "Removal and Installation". Disconnect the harness connector from the NATS antenna amp. Release pawls and remove NATS antenna amp. (1) from the ignition sw ...