DTC Logic
DTC DETECTION LOGIC
CONSULT name |
DTC |
DTC detecting condition |
Repair order |
CURTAIN AIRBAG MODULE LH CIRCUIT [OPEN] | B0021 | LH side curtain air bag module circuit is open. | Refer to SRC-55, "Diagnosis Procedure". |
CURTAIN AIRBAG MODULE LH CIRCUIT [VB-SHORT] | LH side curtain air bag module circuit is shorted to a power supply circuit. | ||
CURTAIN AIRBAG MODULE LH CIRCUIT [GND-SHORT] | LH side curtain air bag module circuit is shorted to ground. | ||
CURTAIN AIRBAG MODULE LH CIRCUIT [SHORT] | LH side curtain air bag module circuits are shorted to each other. |
DTC CONFIRMATION PROCEDURE (With CONSULT)
1.CHECK SELF-DIAG RESULT
Is the DTC detected? YES (Current DTC)>>Refer to SRC-55, "Diagnosis Procedure".
YES (Past DTC)>>GO TO 2.
NO >> Inspection End.
2.ERASE SELF-DIAG RESULT
Erase the DTC using CONSULT.
Can the DTC be erased? YES >> Inspection End.
NO >> Refer to SRC-55, "Diagnosis Procedure".
DTC CONFIRMATION PROCEDURE (Without CONSULT)
1.CHECK SELF-DIAG RESULT
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode. Is the DTC detected? YES >> Refer to SRC-55, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.HARNESS CONNECTOR
Visually inspect all applicable harness connectors for the following:
NOTE: All harness connectors should be inspected from the air bag diagnosis unit to the end component (including in-line connectors).
Is the inspection result normal? YES >> GO TO 2.
NO >> Perform one of the following repairs:
2.CONFIRM DTC
Is DTC still current? YES >> GO TO 3.
NO >> Refer to GI-41, "Intermittent Incident".
3.WIRING HARNESS
Check the wiring harness for visible damage.
NOTE: The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component (including any in-line connectors). Is the inspection result normal? YES >> GO TO 4.
NO >> Replace the harness.
4.CONFIRM DTC
Is DTC still current? YES >> GO TO 5.
NO >> Refer to GI-41, "Intermittent Incident".
5.AIR BAG DIAGNOSIS SENSOR UNIT
Is DTC still current? YES >> GO TO 6.
NO >> Clear DTC. Inspection End.
6.SIDE CURTAIN AIR BAG MODULE LH
Is DTC still current? YES >> GO TO 7.
NO >> Clear DTC. Inspection End.
7.RELATED HARNESS
Replace the related harness.
>> END
Driver side door mirror defogger
Description
Heats the heating wire with the power supply from the rear window defogger
relay to prevent the door mirror
from fogging up.
Component Function Check
1. CHECK DOOR MIRROR DEFOGGER LH
Check that heating wire of door mirror defogger LH is heated when turning the
rear window defogg ...
Sunshade
Removal and Installation
REMOVAL
Remove the moonroof unit assembly. Refer to RF-53, "Removal and
Installation".
Place the moonroof unit assembly (1) on a flat surface upside
down and remove sunshade (2) screws (A).
Manually move sunshade motor (1) using suitable tool (2 ...
C1704, C1705, C1706, C1707 low tire pressure
DTC Logic
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS sensor IDs
Display tire pressure reported by the TPMS sensor
Read TPMS DTC ...