Nissan Rogue Service Manual: Wheel sensor
FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View
- Front LH wheel sensor
- Harness connector
- Slant line
FRONT WHEEL SENSOR : Removal and Installation
CAUTION:
- Be careful not to damage front wheel sensor edge and sensor
rotor teeth.
- When removing the front wheel hub and bearing, first remove the
front wheel sensor from the steering
knuckle. Failure to do so may result in damage to the front wheel sensor
wires making the front
wheel sensor inoperative.
- Pull out the front wheel sensor, being careful to turn it as
little as possible. Do not pull on the front
wheel sensor harness.
- Before installation, check if foreign objects such as iron
fragments are adhered to the pick-up part of
the front wheel sensor or to the inside of the hole in the steering knuckle
for the front wheel sensor,
or if a foreign object is caught in the surface of the sensor rotor. Fix as
necessary and then install the
front wheel sensor.
REMOVAL
- Remove the front wheel and tire using power tool. Refer to WT-57,
"Adjustment".
- Partially remove the fender protector to gain access to the wheel
sensor harness connector. Refer to EXT-
28, "FENDER PROTECTOR : Exploded View".
- Disconnect the harness connector from the front wheel sensor.
- Remove the front wheel sensor bolt from the wheel hub and bearing.
- Remove the front wheel sensor from the strut bracket.
- Remove the front wheel sensor from the steering knuckle.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
- When installing, make sure there is no foreign material such as
iron chips on and in the hole in the
steering knuckle for the front wheel sensor. Make sure no foreign material
has been caught in the
sensor rotor. Remove any foreign material and clean the mount.
- Do not twist front wheel sensor harness when installing front
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that front wheel sensor harness is not
twisted after installation.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
FWD
- Rear LH wheel sensor
AWD
- Rear LH wheel sensor
REAR WHEEL SENSOR : Removal and Installation
CAUTION:
- Be careful not to damage rear wheel sensor edge and sensor
rotor teeth.
- When removing the rear wheel hub and bearing, first remove the
rear wheel sensor from the rear
wheel hub and bearing (FWD) or the rear axle housing (AWD). Failure to do so
may result in damage
to the rear wheel sensor making the rear wheel sensor inoperative.
- Pull out the rear wheel sensor, being careful to turn it as
little as possible. Do not pull on the rear
wheel sensor harness.
- Before installation, check if foreign objects such as iron
fragments are adhered to the pick-up part of
the rear wheel sensor or to the inside of the hole in the rear wheel hub and
bearing (FWD) or the rear
axle housing (AWD) for the rear wheel sensor, or if a foreign object is
caught in the surface of the
sensor rotor. Fix as necessary and then install the rear wheel sensor.
REMOVAL
- Remove the rear wheel and tire using power tool. Refer to WT-57,
"Adjustment".
- Remove the rear wheel sensor bolt.
- Disconnect the harness connector from the rear wheel sensor.
- Remove the rear wheel sensor from the wheel hub and bearing (FWD) or the
rear axle housing (AWD).
- Remove the rear wheel sensor harness grommet from the bracket.
- Remove the bolt, the rear wheel sensor harness, and the rear wheel
sensor from the bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
- When installing, make sure there is no foreign material such as
iron chips on and in the hole in the
rear wheel hub and bearing (FWD) or the rear axle housing (AWD) for the rear
wheel sensor. Make
sure no foreign material has been caught in the sensor rotor. Remove any
foreign material and clean
the mount.
- Do not twist rear wheel sensor harness when installing rear
wheel sensor. Check that grommet (2) is fully inserted to
bracket (1). Check that rear wheel sensor harness is not
twisted after installation.
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation - Front Sensor Rotor
The front wheel sensor rotor is an integral part of the wheel hub and bearing
and cannot be disassembled.
R ...
Other materials:
Component parts
Component Parts Location
No.
Component
Function
1
Key switch
Transmits the key switch signal to the BCM.
Refer to SEC-115, "Component Parts Location" (without Intelligent Key
system) for detailed installation
location.
2
...
Fuel gauge
Fuel gauge
The gauge indicates the approximate fuel level
in the tank.
The gauge may move slightly during braking,
turning, acceleration, or going up or down hills.
The gauge needle returns to 0 (Empty) after the
ignition switch is placed in the OFF position.
The low fuel warning ligh ...
Service data and specifications (SDS)
Wheel Alignment (Unladen*1)
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand
tools, and mats are in designated positions.
Ball Joint
Wheelarch Height (Unladen*)
*: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand
tools, and mats are i ...
В© 2014-2024 Copyright www.nirogue.com